I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
A quick question. I've made an App based on the peripherals not required by the SoftDevice, in particular s112 states RTC0 and TIMER0 are used. I'm moving onto the Bluetooth...
I am able to run all samples from this folder /ncs/v1.2.0/zephyr/samples/ and see the output on the LTE Link Monitor.
However, when I try to run the GPS sample from /ncs...
Hello I notice that exemples with Softdevice ( nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b) works fine for a PCA10056 but not on a PCA10059. When I had tried to make this...
Hello,
first of all let me thank you for providing the nRF Sniffer, which is a great and very helpful tool! I use it a lot and I'm well are that one would have to pay a...
Hi,
I have currently started the development with nRF52840 PDK. I need to get a simple program for a Zigbee coordinator and sleepy end device. I have tried the light example...
Hi team,
I am working on SDK v16.0.0 and using the nRF52840 DK. I generated a new private key public key pair using nrfutil and used that to generate dfu_public_key.c to...
Hi, I want to power the system off when a a characteristic is written. I do so by calling sleep_mode_enter function listed below. When sd_power_system_off is called the system...
hi
i program the hex of nRF5_SDK_16.0.0_98a08e2\examples\ble_peripheral\ble_app_hids_keyboard into pca10056,it run ok .if i don't connect it by phone，and than press button1...
Hello,
I want to test the Thingy Mesh Provisioning Demo v0.7 with the codes provided on the GitHub:
https://github.com/NordicPlayground/thingy52-mesh-provisioning-demo...
Hello everyone, recently i was trying to figure out the best way how to send a large amount of data from ble peripheral to the central (Android device in this case) and thanks...
Hi,
I want to add FDS basedon dimming_serve example ,However,after fds_init(); it not jump to fds_evt_handler but stop wait .
The below is my code:
And The Bellow...
Hi all.
First I would like to apologize for any mistake because I'm posting first time here.
I'm using Visual Studio Code (VSC) to evaluate the blinky example from nRF5...
I recently had the need to communicate with a device over I2C. I'm using the nRF52 as the master. Everything works fine, but power is a concern. I am putting the processor...
Hello,
I have the same problem as this post . The difference is my SPI is sending out junk instead of stucking. I have tried the solution in the original post but no avail...
