I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
When trying to configure custom UUID the nRF Connect, the program fails to find the location of the file.
This is due my username to be "Filipe Aguiar" with a space which...
Hello, Nordic community,
I built and successfully run mqtt_simple project on our MQTT broker using v1.1.0 firmware and NCS.
I edited CONFIG_SERIAL=n in spm and mqtt_simple...
I have one of the nRF52840-preview-dk boards. When I brought up nRFgo and clicked on the board, I was invited to update the JLINK firmware. It was pretty enthusiastic in its...
Hello,
I'm trying to use the zephyr settings module to save bluetooth settings on the nRF9160 DK. I'm using the NCS downstream version of Zephyr . Unfortunately in the most...
1.when i use the example on the dir : examples\ble_peripheral\ble_app_blinky\pca10056\s140\arm5_no_packs
i have sucess flash the softdevice and the app:
the console show...
Hello ...
I'm adding buttonless DFU support to my nRF52810 application using the instructions here . I'm using SDK 15.3.0, SD 112 6.1.1.
First question: These instructions...
I'm using the SPI Manager to send large transfers of data to a graphics controller. What I see is that, once a single byte is transferred, the CS line will continue to pulse...
Hi,
Greetings!
I want to disallow an unknown bluetooth device (like phone, etc) to connect to "secure_bootloader_ble_s132_pca10040" except from a bunch of pca10056 (central...
Again, I'm having trouble with the driver library. Earlier when testing I had SPI working OK as a small standalone test , but now I want to add SPIM to my actual application...
Hi,
two days ago I started checking the usbd_cdc_acm example in order to add usb serial comm functionality to my project. and I have some fundamental (newbie) questions...
Hi all,
I'm trying to add to our application BLE DFU feature. Therefore I'm testing first the secure bootloader example provided in the SDK v16.0.0
I managed to build...
Hi!
I have been using and loving the simplicity brought by the Toolchain Manager (TM).
But now I want to use an application available on the master (Connectivity Bridge...
In an attempt to add a custom UUID to your current project I change NRF_SDH_BLE_VS_UUID_COUNT from 0 to 1. Then loaded the code onto our PCA100040 53822 devkit. At runtime...
Hello I have a nRF9160DK V0.8.5 and downloaded the latest User Guide (V0.9.2) but it does not match my board. Looking at the Revision History section of this document it looks...
Hi!
I've been playing around with the SDK and nrf9160 dk for a week now, and it's a lot of fun.
In the beginning the UART example worked perfectly, and I managed to add...
