Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi All,
I am using NRF5 SDK 17, I have been playing with several examples and noticed that when it comes set up, a peripheral or a priority or clock source there will...
I started modifying the NRF Android Blinky example project to suits my needs (to control a servo motor). I observed there is a BIG delay between writings to a specific characteristic...
Hi guys,
Is it possible to read the data in Minicom if my device is not connected directly with my laptop. Instead of that, I connected my external voltage source to supply...
Hi, I am using the nrf mem_manager library for allocationg multiple dynamic memories in my code. I have done the following
All the devices are getting the allocation for...
I am using a custom board based on nRF52840. Application is working perfectly, and then a new feature was requested. I need to count the number of minutes the application...
Hello guys,
We are developing a device that will based on nRF9160 SiP. We use nRFConnect SDK v1.3.0 . The goal would be to connect to AWS IoT through MQTT and exchange messages...
Hi,
In one module of an application I would like to statically declare a large buffer in SRAM: static uint8_t largeBuffer[65536];
The application fails to link with the...
Hi,
I have been implementing the GPS on my thingy:91 with the firmware v1.2.0
I'm able to do a cold start and get a FIX is if in do not move the board for around 100...
Hello，I am using SDk14.1.Sometimes w hen I send data to nrf52832 via serial port，the code prompted me "APP_UART_COMMUNICATION_ERROR".And t he value of the ERRORSRC register...
Hi, I am trying to perform an OTA DFU of SD + BL on nRF52840, upgrading the SoftDevice from 6.1.1 to 7.0.1.
I have been able to do a DFU of application only, and it works...
Hello everyone. I have the following issue: I would like to connect some Nordic Thingy:52 nRF6936 devices in a mesh network, using the application nRF Mesh . In theory, the...
Hi,
We are in the development stage of a project using NRF9160. We would like to know which one is the stable version of NRF connect SDK. In the , git we can see tags like...
I have a non-secure app targeted at the nRF9160-DK platform and use SPM as the secure app. I can apply a device tree overlay to SPM to enable peripherals from the non-secure...
