I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Dear community,
for my upcomming project I would like to use the nRF52832. Since there also exists a development kit I started to make myself familiar with Embedded Studio...
I have two nrf52 chips connected to each other via SPI
I send data from my Nordic Uart app to my nrf52 chip 1 and I want to send the data that I receive from Mobile app...
Hi,
I'm trying to prepare the firmware for a nRF24LU1+ in order to allow automatic driver installation on Windows.
Based on Microsoft documentation during device enumeration...
I like to provision a node in mesh with the help of computer. Shall i use serial example? Is it possible to use without interactive_pyaci to provision a node with computer...
Hi,
My questions is related to this one: https://devzone.nordicsemi.com/f/nordic-q-a/58250/short-range .
We are also developing board and range is shorter than in smartphones...
Hello!
Does anyone know of a library for the I2C LCD 16x2 display? I found the library by lovee, https://devzone.nordicsemi.com/f/nordic-q-a/23401/nrf52832-connect-with...
I encountered an issue, please kindly refer to the attachment for the detail.
"'' The problem is: a> Run demo on PCA10056 (BLE adv & ANT continuous scan). b> ANT Dongle...
When trying to configure custom UUID the nRF Connect, the program fails to find the location of the file.
This is due my username to be "Filipe Aguiar" with a space which...
Hello, Nordic community,
I built and successfully run mqtt_simple project on our MQTT broker using v1.1.0 firmware and NCS.
I edited CONFIG_SERIAL=n in spm and mqtt_simple...
I have one of the nRF52840-preview-dk boards. When I brought up nRFgo and clicked on the board, I was invited to update the JLINK firmware. It was pretty enthusiastic in its...
Hello,
I'm trying to use the zephyr settings module to save bluetooth settings on the nRF9160 DK. I'm using the NCS downstream version of Zephyr . Unfortunately in the most...
1.when i use the example on the dir : examples\ble_peripheral\ble_app_blinky\pca10056\s140\arm5_no_packs
i have sucess flash the softdevice and the app:
the console show...
Hello ...
I'm adding buttonless DFU support to my nRF52810 application using the instructions here . I'm using SDK 15.3.0, SD 112 6.1.1.
First question: These instructions...
I'm using the SPI Manager to send large transfers of data to a graphics controller. What I see is that, once a single byte is transferred, the CS line will continue to pulse...
