Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
I am using asset_tracker as the basic program and basically it is running fine and sending data to the RF connect web page.
However approximately every 30 minutes I get...
I am looking for a simple example for I2C write. The TWI sensor example is not clear.
It would be great to have an example like the basic SPI example
i.e.
How to init...
Hi, My company is interested in doing bluetooth beacon location tracking of android devices for a VR project. I notice we can easily purchase bluetooth 5 beacons on amazon...
Hi,
I am trying to migrate my project file from Keil 5 to Segger Embedded Studio (SES).
After porting all my source code and configuration files, SES is able to compile...
Hello,
I want "nrfutil" CLI tool (To perform DFU OTA of BLE) for one of my device which is based on i.MX6ULL ARM based processor 32bit.
I found that using "pip install...
Hi,
I am using nrf52840 chip, there is Thread and iot coap library, and movement sensor. When sensor detect move, pin call interruption and send coap message.
Voltage...
Hi all, Within my application I've followed the example/fstorage to the letter however upon requesting a flash write to the s112 the nrf_fstorage_is_busy() function loops...
Hi,
I am working with nRF PCA10056 evaluation board and using SDK 15.2.0. I am using nRF52840 as a central scanner, where it will scan broadcast data from beacons.
I want...
Hello,
I'm having problems with resuming usbdevice from susspend state. I'm working on SDK 15.2 with SD140 (6.1.0). on custom board with nRF52840 IC rev. 2.
My application...
Hi, the power LED no longer turns on on my nRF52840 DK board. The board is still advertising when it is connected to a power source and I am able to connect to it with a mobile...
I'm trying to add PDM into my project but can't get it to compile. When I try to call
I get the error "main() undefined reference to `nrfx_pdm_init'"
This looks like...
Hi,
I have some code written to copy PDM mic data into the external and then later dump it over UART. The issue I have is that when using the external flash, my audio...
Hi,
I am working on a product based on an nRF52832 (SDK 15.3, S112 v6.1) with Secure Bootloader.
I am trying to enable the peer manager with bonding using the Flash Data...
I am starting a new development and want to select an appropriate debugger. I am using Keil uVision Pro version.
I a previsous project I was using ULINK2 and was hoping...
