Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Hello
I designed a custom board and now I have to put the code in the nrf52840 module (from raytac). I have been using the nrf52840dk to write my code and now I want to...
I wanted a COAP Server running on nRF5340dk with DTLS and NS-Target without success. Whenever there is an attempt to connect to it from outside the app freezes, eg. shell...
Hi,
I had a working project for nrf Connect NCS 3.0. I don't know what happened, but now I can't even create a new build configuration. Every time I click on "add build...
Hi
I want to use nRF54L15_DK run RSSI test
I know Desktop App on PC "RSSI Viewer" only Support nRF52 series,
Q1：How can I use Desktop App to run RSSI test?
Q2：Can...
I am currently working on a project involving the nRF52832 SoC using nRF5 SDK v15.0.0 . According to the nRF52832 Product Specification v1.4 , it is mentioned that P0.00 ...
I am receiving packets in monitor mode on a nRF7002DK. I need some advice on how to interpret the signal value. From <modules/nrf_wifi/fw_if/umac_if/inc/system/fmac_structs...
I'm developing a solution using the nRF9160 and would like to confirm the correct method to completely disable NB-IoT mode so the device operates exclusively in LTE-M.
...
By default the GRTC peripheral is not cleared when started via sys_clock_driver_init . This is because nrfx_grtc_init calls nrfy_grtc_prepare , however NRFX_GRTC_CONFIG_CLEAR_AT_INIT...
Hello everyone
I created a custom board with reference to thingy:91 for the antenna part. The board is 50x50 mm in size.
I tested the board and there are no problems...
Hello, I am following the instruction on dev academy - nrf connect sdk intermediate lesson 2 excercise 1, but I can't select data tab on memory explorer.
I can select only...
Hi,
A few months ago, I raised a ticket regarding the integration of SoftSIM into the nrf_cloud_multi_service sample. With the help of one of your support engineers, I was...
Hello,
I have a Thingy91x and I'm having problems using the samples: "Cellular: GNSS" ( https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/cellular/gnss/README...
Hello!
I don't know if there is a way to configure a nrf52832-QFAA's clock source on my custom board software-wise.
Just a disclaimer but please correct me if I'm wrong...
