I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
HI,
Version: SDK15.3,ble_app_template,custom board with nrf52832
I'm trying to change my device name by writing data from bluetooth
when getting 0xdd 0x06 ........,it...
Hi What is the minimum clock frequency that the TWIS module will work with? Obviously the I2C spec minimum is about 100kHz however the device I am communicating with is using...
Hi,
Is it possible to use the modem firmware mfw_nrf9160_1.1.1 (delivered with nRF Connect SDK 1.2) with nRF Connect SDK 1.1?
We will move to nRF Connect SDK 1.2, but...
Hello, we are integrating a BLE board (nrf52832) into our system, and the ble_app_uart example project is perfect for us, so we are starting with that.
What we are seeing...
After reading some questions about the Thingy:91 here in the forum, I start asking myself, if the Thingy:91 without a nRF9160 DK is usable at all.
Any experience with that...
Hi, I'm working on a design with nRF52832 + chip antenna. I'd like to add a PI network to be able to tune the antenna before production.
I'm working with this antenna:...
OK, I have an app that succeeds in starting advertising and then arrives in the main event loop, following which I go to the NRF_BREAKPOINT_COND trap.
Since I do not have...
hi,
I am using Running Speed and Cadence Service structure, when i raise a write command (bt_gatt_write) from the client I was expecting a BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST...
OK, so I have figured out that I can put some of my advertising content into the scan response if there is no room in the advertising packet, but what do I do if there is...
I just bought the nordic thingy91 and managed to connect it to the cloud. but since then the device doesnt appear to come on at all? I thought the battery has died but when...
My application is using multiple features such as BLE UART, Proximity and TWI.
I've two twi sensors triggered when needed. and one of them generate an int to wake up the...
I discovered a bug in nrf_ble_scan_uuid_filter_add. The "Check for duplicated filter" code does not only a partial comparison on the p_uuid_filter with the p_uuid data object...
I have the nRF5340 PDK dev kit and am building the peripheral_lbs sample code using SES on a Windows 10 laptop. I'm able to build the code successfully, but then I run into...
I can't find any documentation about this and my project depends on it.
Would it be possible to read the power usage in volts or any other value through a bluetooth connection...
