Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Hi.
I try to test using ble pc-drivce C library & 52840 dongle on pc.
except custom service. everything is fine.
under below is custom service pic.
...
This seems to be a recurring question. I suspect the Wireshark/nrf-Sniffer setup is delicate enough that minor changes/upgrades in any of the components causes a problem....
nrf52832 , SDK_V15.3 , ble_app_uart sample code , data communication problem.
Hello there...
I use the SDK V15.2, ble_app_uart sample code, on the nrf52832
seems the...
Hello,
Currently working with Segger 4.42 and SDK 15.0
I've searched around the devzone on doing a passkey connection between my server and central.
I've used the ble_app_gls...
Hi, I'm having trouble pairing with Android devices using the SDK's ble_app_gls example, when I try to pairing with any andoid device it throws the following error "couldn...
I Modify my code for 7 buttons from 7 gpios. But my code has a issue at sdk_config.h. The define of GPIOTE_CONFIG_NUM_OF_LOW_POWER_EVENTS is 9. When I built the code and download...
Hi all,
The nRF52832 spec. document specifies that the current consumed in System OFF / No RAM retention / Wake on LPCOMP mode is 1.9uA. However, if I measure the current...
Hi,
A couple of months ago, the Bluetooth SIG published a specification for LE Audio : a new codec and method to send audio data through BLE 5 connection.
Is there an...
Hello,
Few questions about NUS and NUS C please.
Is there any way to know how many TX are pending ?
Are TX notify or indicate ? How to change it please ?
Thank yo...
Hello,
Based on aws_fota sample, I want to replace the line with poll with something that not blocks (because I have another things to manage in my loop). Do someone have...
Hi,
I am evaluating nRF52840 DK as a peripheral with 300ms interval with no timeout (continuous advertising with APP_ADV_DURATION set to 0 ).
I understood that while APP_ADV_DURATION...
I am developing for an nRF52810 target application.
I am using IAR 8.42 with a PE Micro debugger. If I debug a project (call it project A), the linker ROM space starts at...
Hi,
I tried the SDK_DIR\examples\dfu\secure_bootloader\pca10040_s132_ble example from nRF5_SDK_16.0.0 with my custom board with nrf52832 mcu.
I followed this guide:
...
To the kind attention of Nordic support team,
I 'm working on a custom project so that nRF52840 can operate in two different mutual exclusive running modes. A USB operational...
