We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hallo,
I am developing a custom board, based on Nordic Thingy:91. The custom board won´t support BLE, so the nRF52840 is not intgrated. But Communication with the nRF9160...
Do we have any examples of using tcp in non blocking mode for the NRF9160. I used the USP for PSM example as base for my current project but the blocking call seems to lead...
Hi,
I found some thing not seems to be right in SDK 16. I wonder if this is intentional or a bug. Bluetooth 5 max MTU can be up to 512 bytes. I found the definitions in...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
I have a use case where peripheral need...
The documentation for ERASEPROTECT.DISABLE states:
The erase protection mechanism can be disabled in order to return a device to factory default settings upon next reset...
Hi All,
I am using nRF52840 chip in one of my battery powered design. As I could see the datasheet and power calculator says the current consumption of nRF is less in...
Sir i am following this link -> https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.iotsdk.v0.9.0%2Fiot_sdk_app_mqtt_publisher.html
and I have one...
Hi! I'm using the fatfs library to read/write data from/to an SD-card. I noticed the following behaviour:
When I try to write or read data directly after receiving a BLE...
Hi All,
I am using nRF52840 in one of our design. As the P0.18 is the RESET pin, it is tough to route the trace without a pad on via. Hence as I have modified my design...
Hi Friend,
My platform is SDK 16 with S140 softdevice.
I set a gpio for edge trigger interrupt. But I cannot get the correct gpio state if the data pulse is too short...
Hello,
I want to test bluetooth on nRF9160DK. How to do that? I programmed nRF52 on nRF9160DK with hci uart sample and board selected is nrf52840_pca10090.
But how to...
I'm currently trying to add SUPL support to our existing product, and I'm finding that the SUPL library is absolutely huge. Enabling CONFIG_SUPL_CLIENT_LIB appears to add...
Was wondering if anyone knew why this fault might be triggered?
It triggers when I try to use SPI0 and LTE together.
AT host is disabled.
The code stops here during...
While trying to utilize the TEMP peripheral today, I found that after the event handler returns a single reading the application does not continue to run. Any actions that...
Hi,
I got the nRF connect sdk downloaded and I can build zephyr projects for the nrf5340_dk_nrf5340. I somehow fail t find the sample projects as mention in
https:/...
