But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
There doesn't seem to be any validation of the image when updating the bootloader by secure DFU. nrfutil has no switch to generate any crc or ecdsa_signature. The code uses...
Hi
I am making mesh network using Raspberry pi and NRF52 DK. I install bluez 5 and meshctl on raspberry pi. I successfully connected nrf52 dk using bluetooth. I attached...
I am doing this nRF52xx-to-Thingy-52 example: https://github.com/crfosse/Thingy-52-to-nRF52xx I am able to get the led part working fine, but when I finish the instructions...
I am trying to merge Softdevice, bootloader, bootloader setting and application. But unable to do in a single mergehex command. If i do merge seperately ((BL + SD + APP) with...
Hello.
This function from Zigbee SDK 4.0.0 changes configuration of already configured input pin by calling nrf_gpio_cfg_default(ERASE_PIN);
The leds_buttons_init()...
I loaded up pca10056e ble_app_beacon example for SES to test it on a custom nrf52811 device I have built (using BMD-360 module).
I followed the instructions here and removed...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
I want to know the life of FLASH by garbage collection. Assume that garbage collection is performed only when "PM_EVT_STORAGE_FULL...
the python package is not updated through pip with last release of SD_API and corresponding hex files.
I know that you give instruction to build driver but it could be easier...
I am trying to test a simple non-connectable BLE adverstising. I am using the following resources.
1. SDK - 16.0
2. SD - S132
3. Board - NRF52 Development kit.
4....
hardware: nRF9160 DK 0.8.2 firmware: 0.7.0-29.alpha
I want to send data every a few seconds through MQTT. It fails in the first and second Tx after MQTT client initiation...
Hi there,
I am having a hard time with some C pointers to add a new BLE Characteristic.
I would like to have a function that returns a simple characteristic metadata and...
Hi , I am using nrf52840 dk with zigbee cli example in sdk. I have configured nrf52840 as coordinator. I am using xbee pro s2c modules as router in zigbee network. Terminal...
Hi everyone,
I want to send my IMU's readings through BLE to a central. I have implemented the code and notify the central every 1s with the measurements.
I have an array...
Bonjour, je ne peux pas télécharger un firmware via l'application nfr toolbox avec mon Huawei p8 pour mon home trainer connecté, via bluetooth. Je reste bloqué à 2% et un...
