Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
I have an issue with waking up SPI communication after sleep.
Befor I go to sleep I'm disabling SPI communication:
NRF_SPI0->ENABLE = 0;
NRF_SPI1->ENABLE = 0;
...
Hi is there anyone who knows if you can change the time on how often the health server model send out, the health server model is from lightswitch demo
Hi,
I wanna use nrf51822 as master which has 2 slaves: sdcard (fatfs) and adc
I set SPI_INSTANCE 0
and they don't want to work together, I mean I'd like to write some...
A time T_PINR is specified in the datasheet, as shown in the snippet below.
Does this give me an indication of the pulse width for a pin reset? If so, how do I interpret...
Not really a question, just that I find the comment misleading. In the sdk_config.h example coming with the SDK there is this piece of code:
// <q> SAADC_CONFIG_LP_MODE...
Hello,
I am trying to establish communication between Win 10 PC and nRF52 Dev Kit using pc-ble-driver . I followed the instructions in:
https://github.com/NordicSemiconductor...
RN2903 is LoraWAN module using ASCII Command Interface over UART.
RN2903 is connected with nRF52-DK.
I'm connected uart line tx, rx gnd.(cross connect...)
UART communication...
Hi,
My desire is to connect a BC832 module (with nRF52832 on it) to a UART on a controller board and then send data from an iOS app (programmed in Swift) through the BLE...
Hello,
I need two signals with a phase shift to control my motor. For some reason, completely randomly, sometimes my GPIOTE event is not triggered and i get the inversion...
Hi All,
Based on nRF52832 SDK14.2 rtc example, I want to change it to retrigger RTC Compare0, let the LED1 also toggle every 3s, instead of keeping LED1 on. I tried to add...
Hi, guys, I have an IR receiver module with 3 pin (AX-1838HS) ?
How can I use it on my nrf52832 ? I have PCA10040 development board. I don't know how to connect them and...
I need to drive a stepper motor without software intervention, since strict timing is a must.In the following image you can see the required wave-forms - the motor requires...
The SD API (S132-6.0.0) documentation provides little beyond what one could guess from the function and type names. sd_mutex_acquire says "Attempt to acquire a mutex". nrf_mutex_t...
