I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
-HI.
I had previously implemented ESB RF communications with the nRF24l01 + and nRF24LU1 +.
Now we want to implement ESB RF communication with nRF52840 DK(PTX) and nRF24LU1...
Hello,
I am trying to evaluate the "ble_app_uart" in the "nRF5_SDK" and I am using "DVK-BL652-SA-01" development board from LAIRD.
The example works fine for a while...
Hello,
I'm using the "ble_app_uart" example without a problem. I need to add a timer to this example. For this purpose, I copied the content of the " peripheral_timer" example...
Hi,
I’m working on a project where I need to control a device via BLE_Uart. The scenario I’m trying to achieve is: - I have a network of several centrals und several peripherals...
Hi, I'm trying to use Atomic FIFO in my application, where multiple interrupts of different priorities are trying to read from and write to same FIFO. I couldn't find any...
Hi,
The questions:
When is PB-GATT expected to land in the SDK for Mesh?
What are the best Andorid/iOS example apps to act as provisioner and network...
nRF Connect suddenly can not find the COM port to my nRF Dongle. The same setup used to work fine untill today. I reinstalled the nRF Connect, JLink drivers but it is still...
Hi,
I'm using SDK 15.0.0; nrf52840 DK; IAR(EWARM).
I want to add TWI(i2c) from example in SDK to my project.
But I facing with next errors:
Error[Li005]: no definition...
Hi dear engineers,
I have a strange TWI problem on my production protype which programmed based on the official twi example with softdevice s130_nrf51_2.0.1 and SDK 12.3...
Hi,
I'm trying to schedule few events within the shortest connection interval . Is it possible to shcedule 3 events, 2.5 ms long within 7.5 ms connection interval? Could...
Dear all,
I am using the nRF51822 custom developed board. Earlier it was working fine, but now when I try to connect the BLE with nRF ToolBox APP UART service, the APP...
Hi,
Have flashed an early sd_power_system_off first line in main() when measuring power-consumption...
Now the SWD access seems gone. Is there a trick to get it back in...
Hi, I'm working on a custom board with a nRF52840.
I want to use REG0 and REG1 as mentionned in Figure 13 of the datasheet : with VDDH, and both DCDC. My PCB is powered...
