Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Hello,
We are having a peculiar issue with the NRF52 and SDK 13 that I hope you might be able help with.
Having migrated from SDK 12 to SDK 13 with softdevice 4.0.2, we...
Hi,
Im having nRF52 DK and im using CLI example....i have configured through the putty by seeing this https://devzone.nordicsemi.com/f/nordic-q-a/22261/cli-autocomplete...
I implemented DFU secure ble. And implemented encryption. But now I remarked strange behavior. If make same DFU packet (.zip) and flah nRF52 than update firmware for same...
Hi,
Im running CLI program in my nRF52DK.
Im unable to connect using UART or USB as the transport layer for the CLI module but i can able to connect using RTT as the transport...
Hey!
I have some trouble service UUID then i try to use the multilink central example project on a nRF51 dongle. I want it to have contact with a peripheral with sends a...
I'm trying to get a Bluetooth interface (Bluefruit) to the Nordic BLE softdevice under NuttX. Right now it's very unstable. It will work occasionally for 90 seconds and then...
Hello,
When trying to connect to our custom board, it ends in Time out after 5 seconds.
On the board, I put the simple Nordic_Blinky example (\examples\ble_peripheral...
For the custom_ble_service_example , trying to change the service used in the example to a Bluetooth SIG service.
Original is: CUSTOM_SERVICE_UUID_BASE f364adc9-b000-4042...
Quick question: when will the nRF52840 DK available? On the nRF52840 DK page, there is a recommendation to avoid the PDK:
"The nRF52840 replaces the nRF52840 PDK which is...
I have the super typical problem of needing long data transfer greater than the 20 byte MTU size.
I have a basic protocol that has the total length of a long message coming...
Hello everyone, I am very new to nRF52832 Development Kit and was testing some examples to get familiar with this kit, however i encountered an issue while testing the ble_app_uart...
Hello,
We are having problems with Gazell pairing. Both the host and the device are using the Gazell stack from the nRFgo SDK 2.3.0.10040 ported to run on an Atmel SAMD20J18...
