Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Are there any limitations when the central is connected to 20 peripherals at the same time? Is there a minimum connection interval (ie, can I set them all to 7.5ms?).
Hy everybody,
I'm trying to implement DFU bootloader in our custom board, starting from the "bootloader_secure_example", where I just changed leds and button pins in order...
hi,
i am doing nrf_mesh_dfu example with nrf_sdk_for_mesh v1.0.1.
so far i am able to generate device public_key and private key by following instructions .
and also...
Hi, I get a hard fault when I try to add an own UUID to the softdevice S132. I'm using Eclipse with GCC compiler, Rigado BMD350 eval board with the nRF52832 chip on it. As...
Hi Nordic DevZone ,
I wanted to enable the new feature Advertising Extensions in the example application light_switch and see how it works, but unfortunately i can not...
Hi,
i am evaluating the use of the nRF51822-QFxx for our product and made good experience with the nRF51-DK. Now, i would like to layout the custom pcb and i am not sure...
Hi
The definition for nfc_t4t_ndef_rwpayload_set() is that it takes buffer_length parameter.
And the comments state "buffer_length Length of buffer (maximum writable NDEF...
Hello there,
I have developed a board with nRF52840 and a sensor. My hardware and tools setup is:
SDK: nRF5_SDK_for_Thread_v0.10.0_e1c3d11
Thread version:OPENTHREAD...
Hi, I'm using evaluation board nrf52 (nrf52832) and using SDK 13 (nRF5_SDK_13.0.0_04a0bfd) and programing it using eclipse. Here is the code:
Someting is not working and...
I am able to disable the reset function of P0.21 by erasing UICR register and undefining CONFIG_GPIO_AS_PINRESET .
Still i can't set P0.21 as output and set it to 1.
According to the User Guide,
After each byte has been sent over the TXD line, a TXDRDY event will be generated.
When all bytes in the TXD buffer, as specified in the TXD...
Hi Nordic,
We are building a product in the field of Sports, specializing in running shoes. The concept is to correct running form via analyzing the foot strike of the user...
Hi everybody,
I need to preserve 3 pages of data in flash memory during DFU. I know there is the macro DFU_APP_DATA_RESERVED defined in dfu_types.h but, I was wondering...
We need to sample two digital inputs GPIOs at rate of 100khz-1mhz. How can we do that?
The QDEC is only good for up to 128us (~7khz) which is too slow for us.
Is there a...
I'm not able to get clear/un-corrupted data across the ttyACM on the nrf52840-PDK. I must be missing something, seems like this would have been solved a million times, but...
