I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi, i've setuped Clion to build my porject. I've followed this link . Everything works i'm able to build for my custom board, but in zephyr folder I d'ont see merged.hex file...
Hi:
I'm doing the exercise L3-E1.
I used nRF Connect SDK Toolchain v2.7.0 because it didn't work with v2.8.0
How do I make NRF Terminal appear?
Thanks and Best...
Hi,
according to the known issues list for the SDK release 2.5.x x=[0,1,2] and others previous ones, the bug NCSDK-21379 exists (see the link below)
https://developer...
Hello, My SDK is NCS2.8.0, I want to know the version of matter, but I can't find it, may I know how to get?
BTW, does NCS SDK support Matter 1.4.0, if yes, could you tell...
There are two USB ports. IMCU and nrf5340. I had a lot of trouble with bad cables but i found one that works and I find that I have a jlink drive that pops up so I know there...
I have finished developing an application, utilizing the nRF 9151 DK, and I am now working on transferring the firmware to a custom board and testing it. However, when creating...
We are developing a very low power product. In some cases like not getting registered, PSM not being available, ... we want to drop the connection and go to a sleep state...
Hi Nordic team,
We’ve implemented a custom firmware update flow for our nRF5340-based device , which supports a robust single-image FOTA process using external NAND flash...
Build configuration is: SDK: nRF Connect SDK v3.0.0 Toolchain: nRF Connect SDK Toolchain v3.0.1 Board target: nrf52833dk/nrf52833
All other values left at defaults.
There...
I had like three Thingy52s for a project and have just come back to it after about a year.
The batteries are now dead and the device does NOT seem to want to charge.
All...
Hello,
I've a battery based device that uses a buck/boost to efficiently use entire battery voltage range (4.2-3.0) . This component have a low quiescent current between...
Hi As part of attempting to write code for self testing I'm trying to measure the HFXO frequency using the LFRC (we don have an LFXO) I'm expecting that the measured HFXO...
I am reaching out to seek your guidance on a development project involving the nRF52840 and Semtech SX1262 LoRa transceiver.
We are building a marine crew monitoring and...
Hi,
The following URL does not include nRF54L15, is it supported?
https://docs.nordicsemi.com/bundle/ncs-3.0.0/page/nrf/samples/openthread/coap_server/README.html
...
