I am trying to use the FIFO from the ADXL362 with in the Thingy:53. As I noticed there is now the Option to use ADXL362_STREAM. I just wanted to use the example from: https...
The specification for the nRF54L15 states that the typical current consumption for I_TIMER3 (TIMER10 running) is 240 mA/milliamps . The other timer values in the table are...
The Nordic Thingy:91X was initially unable to connect using certain SIMs (e.g., Airtel IoT) due to lack of NB-IoT support or no signal.
After switching to a Jio NB-IoT...
Hi to all,
I am trying to do a ZUTH (Zigbee unified test harness) test run, using the Silabs devices as golden devices (as per CSA recommendation) and nRF 52840 dongles...
Hi
I am trying to port some PWM code from the NRF54L15 it uses HAL access because i have found it has faster writes which are useful for my application (testing latency...
Hello,
I have recently upgraded from v2.9 to v3.0.1 and have noticed that the mesh security has changed from CONFIG_BT_MESH_USES_TINYCRYPT to CONFIG_BT_MESH_USES_MBEDTLS_PSA...
Hello.
We're trying to expose and use the Wifi stack in micropython in our project for the nRF7002. We've managed to get Wifi scanning to work (based on the sample code...
Hi All,
1.One master BLE has to connect to Slave BLE, then both device should read other RSSI and sent the data through UART.sending the RSSI should be every 200 millisec...
Hello,
I try to use those functions for printing log massages on the Segger RTT terminal, but I have many problems with that.
1. How can I use this function without printing...
Hi everyone,
I am using nRF52832 kit (PC10040), eclipse and softdevice S132 V5.0.0 for developing a BLE service. I follow the service tutorial and I refer to the code from...
i want to connect raspberry pi 2 with nordic thingy 52 via ble.....while issuing connect command after gatttool -I -b Mac addr it is throwing some connection refused error...
i want to know about how nrf51822 module's states will change once it is turned ON.
with the state diagram i can define how the module is working after turning it ON.
...
All,
I'm relatively new with the Nordic Ecosystem and have been playing with the example projects on the nRF52 DK and have successfully gotten several examples up and running...
Using Keil v5, ARMCC 5
Pin state equals:
Level 0 - 0x00000000 - pin low
Level3 breakpoint after read - 0x00000040
Level3 breakpoint before and stepped through -...
I am advertising a service and providing scan response data. It is not clear to me whether I should be bothering setting up the values of the ble_adv_modes_config_t structure...
Hi there,
i am very curious about what can be considered as interrupt factor in receiving the signal from beacons, so if these scenarios have been tested please provide...
I'm using the nrf52832-QFAB variant (32K RAM 256K Flash)
The part is marked as NRF52832 QFABB0 1630AC
Surprisingly, this part is happily running my application and bootloader...
Hello,
I can't find where in flash the peer manager data is stored. I'm currently working on DFU support and as part of that I want to define the memory area that should...
As per mesh_hw_resources.md (MESH_SDK/doc/introduction)
## Flash lifetime The flash hardware can withstand a limited number of write/erase cycles. As the mesh stack uses...
Hi all,
I am trying to develop the BLE Heart Rate Collector example on the nrF51 Development Kit. As far as I read in the Nordic web ( http://infocenter.nordicsemi.com/index...
