Hello, We're developing a firmware for our board based on nRF9160, using ncs 2.7.0. We want to allow the user to set the certificates over i2c. How can we in a secure mode...
We are developing an IoT device that utilizes the nRF9151. We would like a review in the second round of our schematic and layout to understand if there is any issue that...
Hi
Is it possible to stream 128 kbps .acc, .lc3 or .mp3 Spotify audio from server to nrf9151 ?
It says it supports 300 kbps download, so maybe 150 kbps is realistic ?...
Hello,
I'm currently working with a custom board using the nRF5340 SoC, and I'm running into unexpected current consumption behavior.
When the device is in advertising...
I installed NRF connect I successfully built project when I flash I get success, but actually I can see project is not flashed what and how can I debug that ?
Hi,
I am using the nRF52840 with nRF-SDK version 16.0.
At random intervals, I encounter the following error:
"[00:02:51.009,460] <error> app: ERROR 1813 [Unknown error...
Hi everyone,
We found that the LIS2MDL_INT interrupt from the compass on P1.06 affects communication between the app core and the network core.
About 3 seconds after...
So I reinstalled one of my Linux boxes (again) a few days ago, and one of the things I need to do to get all the development environment up and running (again) is get the...
Hi everyone,
I'm currently working on MAX30100 sensor and i need to read this sensor data with i2c, currently i'm able to read mpu6050 and 9255. However i don't have much...
Hi all,
My BLE device uses the NUS profile to send data to a connected smart device. At the same time it should also be possible to connect to a RPi/Linux based gateway...
I now use nrf52832 to do development, nrf52832 and mobile phones to transfer the data is relatively large, I would like to achieve For mobile phones that support BLE4.2, a...
Hi Everyone,
I have been experimenting around with the low power SAADC example in SDK13.
I am using PCA10040 dev board and I have programmed it to start/stop ADC sampling...
Hi,
We've been developing an peripheral HID over BLE using Nordic's SDK, connecting with iOS, Android, and Windows devices. (Board: nRF52832, SDK 14)
We've noticed an...
Using 2.0.0-1.beta on Linux Mint 18.
Have installed pyserial with: sudo pip install pyserial --upgrade --ignore-installed
resulting in:
Installing collected packages...
hi ;
now after i maked a successful connection between smart phone and nrf51822 and i could change the state of gpio pin 20 i find a new problem
i want my pin is still...
Hi All,
Just wondering if i'm doing the right thing here.
So i am using the example of the central device to get started.The idea i'm trying to do is to use the central...
Hi,
I am working on my production hardware with nRF52840 on it. I am using MBED OS. What should be the memory map of 52840 for soft device and Application code? I am using...
Here are my system requirements:
A single "Controller" needs to send 4 bytes of data per node.
There are 25 nodes in a system (100 bytes total payload).
All nodes must...
Hello,
Is it possible to use Mesh SDK and create a GATT database for mobile device to connect to? There are no examples for this in Mesh 1.0.0 and 1.0.1 except a simple...
Devzone,
I'm working with the nrf51822 dev kit- specifically with master emuator API version 2.1.8.
Does this current release of the API (2.1.8) or subsequent releases...
Hi Everyone. I am Anthony, embedded software engineer. Now I need to dive into the Nordic BLE world for the new project. And we are going to used nRF51822 MCU. But I have...
