hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
Hello I was trying to run the Power Profiler Module with nRF Connect but I geting the following error:
ps: The python solution is already working for me.
What is the RTC run current on the nRF528120? It is not listed in the datasheet.
In addition, what is the run currents for the clocks on the 810? There is no information...
I need to send data from PC (windows 10) to nrf52832 using UART (hardware) in order to retransmit this data through mesh network with light switch example.
Do i need to...
Because I'm using PTR9618 module of nRF52832, it don't have XTAL 32.768Khz (X2).
When Makefile have NRF52_WITHOUT_SOFTDEVICE=1, hello-world, blink-hello work fine. But when...
Hi,
I'm looking to generate a clock signal on a gpio with an exact frequency. I tried this by setting the pwm base clock and adjusting the top value but got no luck.
Is...
Hi Nordic,
I find somethig wrong while using GPIOTE.
I.
First I call nrf_drv_gpiote_out_init(MY_PIN, &my_config), it works fine. However, I call nrf_drv_gpiote_out_uninit...
dear sir
i had use the ble_ant_app_hrm demo to test ant+ble,but i could not find the softdevice in the folder,so i can't connect it to my mobile phone,the link address is...
Hi, I'm using Central multilink example to connect with our Custom Peripheral sensors. I'm using board PCA10040, nRF52832, SDK_14.2.0, s132. Sensors have a custom service...
For NRF51 and NRF52 antenna matching network, is there any requirements for resitors? Tolerance?
I know there are some requirement for capcitor and inductor types, how...
Hello,
Can we combine a 5-certified hardware circuit with a softdevice that is 4.2-certified? (at examble mbn52832 (module) with s332 (Softdevice))
If yes, with which...
Hello dear
I have a question about NFC on RF52832. On section 42 of datasheet, says:
"The NFCT peripheral (referred to as the 'NFC peripheral' from now on) supports communication...
hello support team,
i have seen thread and sdk14.2.0/examples/peripheral/SAADC example
pca board: PCA10040
can anyone suggest how to read battery status using handler...
Hi,
I am trying to set an nrf52840 pdk (with SDK14 and s140_nrf52840_5.0.0-2.alpha) as peripheral and central at the same time and another nrf52840 pdk just as a peripheral...
