Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
Hi
The definition for nfc_t4t_ndef_rwpayload_set() is that it takes buffer_length parameter.
And the comments state "buffer_length Length of buffer (maximum writable NDEF...
Hello there,
I have developed a board with nRF52840 and a sensor. My hardware and tools setup is:
SDK: nRF5_SDK_for_Thread_v0.10.0_e1c3d11
Thread version:OPENTHREAD...
Hi, I'm using evaluation board nrf52 (nrf52832) and using SDK 13 (nRF5_SDK_13.0.0_04a0bfd) and programing it using eclipse. Here is the code:
Someting is not working and...
I am able to disable the reset function of P0.21 by erasing UICR register and undefining CONFIG_GPIO_AS_PINRESET .
Still i can't set P0.21 as output and set it to 1.
According to the User Guide,
After each byte has been sent over the TXD line, a TXDRDY event will be generated.
When all bytes in the TXD buffer, as specified in the TXD...
Hi Nordic,
We are building a product in the field of Sports, specializing in running shoes. The concept is to correct running form via analyzing the foot strike of the user...
Hi everybody,
I need to preserve 3 pages of data in flash memory during DFU. I know there is the macro DFU_APP_DATA_RESERVED defined in dfu_types.h but, I was wondering...
We need to sample two digital inputs GPIOs at rate of 100khz-1mhz. How can we do that?
The QDEC is only good for up to 128us (~7khz) which is too slow for us.
Is there a...
I'm not able to get clear/un-corrupted data across the ttyACM on the nrf52840-PDK. I must be missing something, seems like this would have been solved a million times, but...
I recently experienced an issue with a race condition between peer manager and FDS in SDK 14.2 which was resolved under this case:
https://devzone.nordicsemi.com/f/nordic...
Hello,
I develop entirely on Linux and I am unable to find the --sd-req / --sd-id required for generating a dfu package zip using nrfutil . I am using developing for the...
I defined custom service (NRF51822,S110) to send sensor data. Code follows. Here I enabled notifications for new data. I can able to receive data, if I enabled notification...
Hi,
I have the following set up:
The remote: nrf51822 acts as central
The wheels: Each wheel has nrf51822 acting as peripheral.
The remote needs to first connect...
My application needs to be notified of large current draws due to the activity of the nRF8001. The active signal works fine for this purpose, but why is it available only...
