I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
I have a project where we have 2 nrf51 that need to be time synced with eachother.
The problem is they are placed on the body one on the back and one on the chest of a person...
SDK 16.0
nRF 52 DK
LIS3DH Axis sensor
I am trying to understand the sdk_config.h about the NRFX_TWIM_ENABLED config. Here the 'M' stands for Manager or Master? If I...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image. I am using ‘ble_app_blinky’.
1) In Product specification, it says 2...
I'm developing a USB Keyboard Receiver. But I founed that there's no APIs and no descriptions about HOW TO SEND CONSUMER KEY and NORMAL KEY in USB HID mode.
I find a lot...
hello：
I want to communicate with my nrf25U1 USB dongle. So i add some code（refer to the examples\proprietary_rf\gzll\gzp_desktop_emulator）. When i add add these files(nrf_gzp...
Hi, Everyone
I am developing with SDK 15.3.0 and nRF52832
Compiling "examples \ secure_bootloader \ pca10040_uart_debug" and "examples \ secure_bootloader \ pca10040_uart...
I can't find anything on this error on Nordic support or Segger support sites. I've looked into the obj directory and only find one main.o file (of course!). Can't see anything...
Hi. We are using a BLE module based on Nordic nRF52832 in a new product we are developing.
The nRF52832 & softdevice has its own QDID - 115277.
However the module also...
I am trying to get a project working with a main.cpp file, some C++ modules, and the 16.0.0 SDK using the IAR compiler. However, using the nrfx/mdk startup files, it never...
Hi,
Iam running the BLE uart and Zigbee light multi protocol example. Using the latest thread and Zigbee SDK v3.2.0. The example is quite good. That the door(Zigbee+BLE...
Hello.
I would like to make simple GPIO bridge. That means transmitter with Digital input and receiver with digital output. When the state of DI changes, it's transferred...
Hi everyone,
I am using nRF52 DK with 52832 on it. My current SDK version is 15.2.0. I know that for IoT applications there is external hardware needed as router like RPi...
Hi,
I have a problem with a specific Zigbee certified device that I can't connect to my Nordic device.
When trying to connect to the device, I go to see the status:
...
Hi,
In need to debug my application using segger IDE when there is bootloader already present in nrf52832 chip .
The sdk we are using is SDK 15.3
Bootloader:- "secure_bootloader_ble_s132_pca10040...
Quick project overview:
Mesh network using nRF52840.
Nodes need to be able to be controlled individually (setting GPIOs) and also report back data (ADC, GPIO state) to...
