Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hello,
I have tested and verified the code for my application on the NRF52 DK, but now I need to program my own custom device using the nRF52832 chip. I saw there was a...
Some bugs in ble_app_hrs_freertos example from the SDK when handling buttons: (at the end of this listing are same tests but with ble_app_hrs (no rtos) and buttons are handled...
Hi, We are working on Thingy91(nRF9160-pca20035). When thingy91 connected to system through USB, We getting BLE UUID values through nRF52840 on nRF9160(on nRF Cloud also)...
Hello,
I am porting a software to the nRF52 SDK16.0 . This software uses Floating Point numbers with Exponent-Byte=0x7F to signal Error conditions (then treated as unsigned...
Hi. I want to evaluate the current consumption of the nrf9160 module (I have a Thingy91) and I want to disable all logging functions. I started with the mqtt_simple example...
I have a characteristic with variable length and max length of
NRF_SDH_BLE_GATT_MAX_MTU_SIZE - 3
i.e. the max possible data length based on the max MTU.
During connection...
My Thingy:91 was added to nRF Cloud using "+" > "LTE Device" and then "Already have an active SIM? Skip this step" (iBASIS roaming doesn't work properly in Switzerland so...
I've been trying to get the MQTT simple sample started however after changing the hostname to "mqtt.eclipse.org" and running the sample, it stops with this error. Please how...
Hello, I am using NRF51822. I want to run UART communication on two different baud rates for 2 different hardware on pin number P09(TX) and P11(RX) respectively. I have to...
The queued writes library provides AUTH and EXECUTE events, but I think it also needs a CANCEL event.
In my code, when I receive an AUTH event I obtain the data buffer using...
Hi,
I got a brand new nRF916 DK. I updated the modem firmware to mfw_nrf9160_1.1.0 and updated the application firmware Asset tracker with nrf9160dk_asset_tracker_nbiot_legacy_pco_2019...
I have set up a PA / LNA and watched the radio details.
When the connection interval was 50ms, it was confirmed that the device was communicating every 50ms.
Look at...
Hello
I want to program and debug NRF52840 dongle using jlink But the jlink is not able to find the target . i am using SEGGER J-Link Commander V6.60d application for flashing...
Hi, Sir:
I am using nrf9160 to develop a project of mqtt and GPS, using mqtt to upload GPS data to the cloud server; I use the software and hardware information as follows...
