Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
We are using regular RIGADO/U-BLOX modules (BMD300 and BMD350).
Do we need to pass PTS tests when we use Bluetooth layers (Softdevice S132_nrf52_5.1.0) with customs services...
Hello,
I'm new with ANT protocol. I read the documentation and I'm pretty comfortable with it now.
I started to develop with NRF52832 (SDK 16 and ANT stack from thisisant...
Hi there, I am a Novice in RF Board design/Antennas, particularly with nRF52 series so I have some quick questions ..
1)What are the Antenna Options for nrf52840 in mesh...
Hi,
I am using nRF52840 and nRF SDK 15.2 and nRF SDK for Mesh 3.1.
When I try to send acknowledged messages, sometimes my device needs to retry several times before the...
Hi,
I am looking for suggestions in regards to which ble example I should use. Currently, I have the hardware that writes data to a flash. I am developing the firmware...
There are several tickets from users trying to get the combination of Zephyr and Segger Embedded Studio (SES) to work on Mac OS including Catalina, but some are unresolved...
Hi,
I want to do an DFU OTA in nRF52840 BLE chip.
I have flashed mcuboot bootloader and also flashed hci_uart (To scan BLE beacons) application. This will be one time...
Hello to all,
I have a problem relating to cluster reporting: I have a device, Window Covering Device, which acts as a router and I want to connect it to Alexa, which acts...
Hello, guys.
Here they are - Thingy:91 and nRF9160-DK boards on my desk!
I was able to successfully register Thingy:91 on nRF Cloud (both SIM card + LTE modem). However...
Hello All,
I was reading about the startup code and vector table of Cortex-M4 (STm32, Tm4c123). When I tried to find out the Vector table of NRF52832 in the datasheet I...
Hi,
This is my second post about this issue, but I have not solved yet. The issue is, that I am using bpwr tx example (crank torque sensor type) with Garmin edge 520plus...
I am developing an android app which is connecting with this product. In that particular case my app advertises, the nRF scans and initiates connection with my app. Some phones...
Hi Nordics,
we would like our central nRF52840 to have DFU timeout in 20 seconds , if no connection received via nRFconnect phoneAPP to perform the firmware udpate, then...
