Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
I am using GPIO interrupt event.
And I added the following code because I wanted to observe PA / LNA.
Adding this code stopped the GPIO interrupts. Can the two coexist...
Hi,
For nRF82540 dev board, the secure bootloader code has embedded many NRF_LOG_DEBUG(...). But they are not displayed or output to virtual COM port. Is there anyway to...
Hi all,
I'm looking to develop a proprietary start network that may support around 30 devices, with very low bandwidth (pretty much just a keep alive and a sensor state...
I just came upon a blog post from ARM about the use of the Cortex-M4's FPU:
https://community.arm.com/developer/ip-products/processors/b/processors-ip-blog/posts/10-useful...
Hi, I am looking for sample code that can reconnect to bonded devices and share the encryption keys with DFU-OTA.
I have worked using DFU-OTA (JUST_WORKS option); I question...
hi all,
i can't update new nrf cloud certificate
"There was an error generating the certificate: No Nordic product with device id nrf-xxxx...(imei)and ownershipCode...
Hi.
I have a Thingy91 that I will use as a remote wake up for another system. I am trying to estimate how long the system will be able to run on a single charge with the...
Hi!
I am trying to find an example project for the Rigado BMD-340 eval board, or some guide to getting running with this board. We are working on a new product using BLE...
Hello,
I am using peer manager to handle security and bonding. Everythin works fine (bonding witth MITM).
However, when a known peer connects, I am getting 6 (six) PM_EVT_PEER_DATA_UPDATE_SUCCEEDED...
I want to make The Thingy91 a bluetooth peripheral device . I want it to send the generated temperature data to cloud or another device. How do I do this? I had problems with...
Hi Nordic Team,
Please share logic to scan specific peripheral devices which are advertising with a filter other than filter for device name, uuid, short name and MAC address...
Hi,
I am using nRF52832 with SDK v16 with s112 BLE stack.
I am trying to enable the DIS service like below:
The device can boot successfully but when I checked the...
Hello,
I want the scanner to receive both AUX_ADV_IND PDU event and AUX_SCAN_RSP PDU event for the case when AUX_SCAN_RSP PDU will be lost I still want to have AUX_ADV_IND...
Hi,
I am using RTT log with nRF52832, my question is when debug port is disconnected, what will happen to RTT logger?
Will they be simply ignored? or will the debug pins...
Hi.
I want to measure the current on the nrf 52840. I have downloaded the beacon example on the board and I want to measure current when the beacon is transmitting(LED 1...
