I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Dear Sirs,
We are creating a solution based on your chip, but have heard that it is / might be discontinued.
If that is the case, what would be the replacement model...
Nordic SDK 15.3.0 ble_app_gls merge with custom service
Hello I am new on KEİL and NRF52832,
I am trying to merge this custom service and Ble_app_gls example . I added...
Hello
Would someone ,please reply to the below thread,waiting for the response
https://devzone.nordicsemi.com/f/nordic-q-a/60891/unable-to-read-the-128-bit-uuid-with-base...
Hello how are you?
I'm using the mesh example Light switch example from nRF5 SDK for Mesh v4.0.0. I implemented the RSSI util model and it is working, one question I have...
I am working on a new design and i am using ST7789 (240 X 320 pixels) screen with nRF52840, it is working fine. I have followed the code provided in SDK example (big thanks...
Hi,
I´m trying to add a new, custom TX characteristic to Softdevice. I use example from SDK 16 "UART/Serial Port Emulation over BLE".
How I can do this, is explained...
Hi,
I flashed and run "ble_app_uart" example on nrf52833 DK. With an UART tool, I can recieve data from smartphone (rx characteristic) but I can´t send data from UART tool...
The sdk 16 - bootloader positions s140 softdevice V. 7.0.1 wrongly so that it is acknowledged as Application and does not work with nrf52840.
As you can see at the picture...
Is there a place to make suggestions for new releases of nRF5 SDK's or even contribute?
I've been using the current USBD CDC ACM library and needed to modify the app_usbd_cdc_acm...
Hi , I am making a zigbee application to write attribute on remote node. Please share the application structure to implement writing functionality of attribute on remote node...
Hi,
I am trying to test PSM settings on the nRF9160 using a custom PCB. I have set the active time to 3 minutes with a periodic TAU time of 10 minutes.
When the device...
I’m developing an application based on pc-ble-driver to talk to an nRF52840-based dongle (from Fanstel).
I’m having trouble disconnecting cleanly when a connection has operations...
Hi,
I´m using the NRF52810 device and have an issue with the SAADC peripheral.
I basically have 2 channel where i want to do some averaging to improve noise.
The setup...
