Hello,
We are currently evaluating a very low power application using the nRF5340+7002. Our hardware design includes a complex power supply configuration, and we need to...
Retrieving Custom Firmware Version from nRF52 BLE Controller to nRF9160 Host
Product: nRF Connect SDK v2.6.0 Hardware: nRF9160 (Host) connected via UART to nRF52832 (Controller...
Hello,
I recently got a BL653 Click Board and am trying to program it. As I do not have a supported MCU for the NECTO Studio IDE (the ClickBoard's manufacturer IDE), I...
Hello,
I am designing a custom PCBA based on the nRF7002DK PCBA and I really need the Fabrication Notes / Drawing that officially went to the fabricator to direct the build...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi all:
To saving power I implement the function to read data after interrupt is triggered..
below are my codes..
My expectation is..
Let CPU enter idle mode to wait...
I am trying to set up a GPIO interrupt, and found that whenever Button 1 is pressed, if Button 1 or 2 is pressed later, the app will reset. This is even if there is any other...
Hi.
I want to make a device which can connect each others and communicate with NUS.
I need not to use any other service without NUS.
I made nus_c service which is a central...
Hi
I can't seem to find this in the datasheets, what is the active current consumption of the nRF52832 chip, I'm interested in the maximum expected current consumption...
Hi!
I want to connect a nrf51 dk with a beacon and I'm using the UUID to make the connection. In the beacon code I define the UUID in this way:
ble_uuid_t adv_uuids...
I use nrf52832 with softdevice s132_nrf52_1.0.0-3.alpha for a ble application on own pcb.
first I'm not sur of adresse to use for iROM and iRAM areas. I've this parameters...
//Hi Everyone!
//I am programming a nRF52832 through the SDW interface and am having trouble answering some questions.
//So, first off is simply checking my understanding...
I have a recent dev board and am using SDK11 with gcc.
I can build and flash OK
The blinky sketch runs
However, when I load up examples/ble_peripheral/ble_app_proximity...
We bought the Beacon Kit from Nordic. I'm trying to use the firmware code on a similiar beacon board based on same Nordic Nrf51822. The board has same button and led pins...
The release notes for the S132 V2.0.0.0 SoftDevice indicate it's only compatible with silicon revisions C and 1.
I have several PCBAs that have the rev B silicon. Will...
Hi guys
First of all, I know nRFgo can be very convenient for application encryption, but in order to improve the mass production efficiency,I merged the application code...
Hi!
Goal: I want to send as much data as possible using CoAP.
I have connected a nRF52 (IoT-DK) to a Raspberry Pi using BLE and 6LoWPAN. The nRF52 is running the CoAP...
I use the nrf52832 with softdevice S132 s132_nrf52_1.0.0-3.alpha for a ble application.
without the softdevice, the rtos works correctly.
but when I enter this parameters...
I'm moving from nrf51 to a higher performance uC. I think that there is lot of models of nrf52.
what's the reference of the best nrf52 in term of performance. I want to...
I've been using the device firmware update service for quite some time now. I'm looking to add the ble_nus service, but this feature seems to fail when ble_dfus is re-enabled...
