I just want to double check something before I optimise an implementation.
If burst is enabled on multiple channels, let's say x256 for two channels, internally is the process...
Hi
I have two DKs, previously they work well, however, after I add the nRF21540 FEM on each DK, I always receive this in my central device:
Whether the amplifier cause...
Hi, I am currently trying to get through the NRF connect SDK fundamentals, I am on lesson 3 example 1, creating an application. The problem I am running into is that I cannot...
Background - We are laying out a new board, upgrading to the nRF54, and wanted to use p2.02 and p2.03 as serial UART lines because p1.04 and p1.05 were planned to be used...
Dear Nordic,
I am debugging a custom hardware with a nRF7002 on-board, using wifi shell app. At this moment the shell does not work as expected, needs to locate where the...
I am attempting to install nRF Connect SDK along with VS Code on an offline machine for development. The main two issues I have are:
The NRF Connect for VS Code plugin...
Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
I tried to upload application through BLE DFU in MCP. The DFU Android app works fine. However, it always failed in MCP.
SDK 6.1.0
SoftDevice 7.1.0
MCP 3.7.1.8567...
Hi,
I have following use case. The write operation on one of the characteristics triggers some UART job which takes about 1 / 1.5 seconds to complete. After the completion...
Hello,
I try to use the S310 V2 but got stuck into problems.
in order to start the application from bootloader in the S310 V1 I did succesfully :
void (*application...
Hi,
I have problem on compiling bootloader example which is located at
\Nordic\nrf51822\Board\nrf6310\device_firmware_updates\bootloader
When I try to compile the...
Hi,
Some questions in example ble_app_hids_keyboard/main.c
Why set the adv_params.timeout to zero in BLE_DIRECT_ADV (Line 779) ?
That will cause no BLE_GAP_EVT_TIMEOUT...
I just got a nRF51 and am having trouble getting started with it. I created a very simple program using the mbed compiler and produced a hex file which I now wish to flash...
Hello,
I see that the make files that have been included have provision to remove dead code from the projects to reduce code food print. This is accomplished using the...
HI folks,
I have checked the current consumption while connected on an average to be 325uA (with uC taking 4.5uA) so this mean almost 320uA being consumed by the nrf8001...
I have a general question about the RF frequency tolerance of Nordic devices in general. Is the following calculation correct?
Crystal spec = 16MHz, +/-50ppm tolerance...
Are there any plans to add boundary scan functionality to assist ICT testing? If not, are there any other hooks into the part that can be used to test during ICT?
Hello
I'm using a pstorage_register from pstorage.c to register two application storage blocks in flash memory. But I have situation that first module have 6 blocks of...
Hi,
are the GPIO pins broken out on the nRF51 Dongle configurable and can be used for SPI Slave tests? I have a running system powered by a ARM Cortex 4 (Teensy 3.1) and...
We have an early implementation of the v6 SDK DFU ported to support S310 on a handful of devices in the field and need to update them to a new bootloader and we'd like to...
Hi,
With the validation of the BLE V4.2 specification will Nordic be implementing the new features of the spec and if so do you have any idea of availability and dates. ...
