Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
We have some old stock of the nRF51822 pre 2014/8/20. Was there a change to the product around that time that would prevent us from using from using this stock?
Many th...
Hello,
I'm using FreeRTOS on nRF51 and I would like to use task notifications instead of semaphore to simply manage task's syncronization.
To test its operation mode,...
Hi, I just copied the antenna drawing by referencing the PCA10040 v1.1 and checking the white paper (λ/4 printed monopole antenna for 2.45 GHz) .
I didn't have much knowledge...
Hi,
How is the functionality of P0.21 in nRF52832? It is configured as RESET after turning on the device, right? Is there any way to change it in a way that that the chip...
Hello DevZone,
I am using a nRF52840 for project development.
To test SPI setting is correct or not, I am doing the loop-back test, I set the MISO and MOSI PIN according...
Hello,
I try to configure two nrf52832 devices work with payload of 200 bytes (data should be 200 bytes, not the all ble packet).
I took ble_app_uart_c peripheral and...
Hi all,
Using UART is confusing for me because I see various implementations in the documentation. There is a Serial library, then there is the UART driver and HAL. The...
I am trying to use the comparator to wake me up when a potentiometer is moved a certain amount.
Before I sleep I read the ADC value of the comparator and use this to set...
Hi,
I'm trying to set up the connectable/scannable advertising. I took the app_beacon example and changed advertising parameters.
My final set up is:
The ADV_INTERVAl...
I have the preprocessor define CONFIG_NFCT_PINS_AS_GPIOS in my code, and GPIO functionality for P0.09 and P0.10 are working just fine for me...
My issue is that even when...
Hello!
I'm a beginner with Nordic products and I'm taking over the nRF52840 Preview Development Kit.
I want to send advertisings at regular intervals (every second...
Hi,
Is it possible for an 3 party BLE device like an mobile device like an Android/IOS Phones or ESP etc to participate in mesh notwork if so is there any documentation...
I have been unable to perform a DFU over BLE using the bootloader_secure_ble example.
I am using SDK 14.0, nRF52832, S132 with a custom board, along with the nRF51 Development...
