Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Dear Sirs, good afternoon
I am working in a design that includes an nRF52840 as main processor.
I need to know if it is possible to have the following peripherals implemented...
Hi,
How do we fuse the debug port on nRF9160? The purpose is to block all access and the ability to erase all from outside.
This is my understanding:
From debugger...
My nrf9160 connects to AWS when using the AWS FOTA example. However, when I start the custom job as setup from the following link:
https://developer.nordicsemi.com/nRF_Connect_SDK...
Hi,
I have a board that emits 0x1818 (Cycling Power) using the nrf51422 chip and firmware using S310 and so forth. Working great :)
Now I just found some strange things...
Hello guys!
We are using nRF9160 SiP module to transfer MQTT messages to AWS IoT. So far, thanks to the cloud_client example and your documentation from here , we were able...
Hello,
I am using Segger Embedded Studio (SES) to develop with the nRF5340 BLE chip. From what I've read, the nRF Connect SDK and Zephyr OS is not tailored for use with...
Hi,
I would like to check my understanding of PSM. Currently, using the AT Client on the local NB-IoT network, I can see that the device is entering PSM after 3 minutes...
Hi, I'm looking for a simple example on how to implement I2C. I've built I2C on my various FPGA's, implemented I2C on various AVR based chips from special function registers...
Good afternoon,
I first devoloped my app based on the nRF52840 (SDK 15.2; S140 V.6.1.0) and it was perfectly working with or without bonds.
After that, and following what...
I've been doing some development on the nRF Mesh platform for the nRF52832 chipset and I'm relying on the Mesh DFU protocol to update my deployed units. Recently I've been...
We need to know what the total internal capacitance and inductance is for the nRF9160 SIP to comply with intrinsic safety certification. Can anyone point me to this information...
Hi, We have developed a custom board. We can upload code using nrf52840 sdk-ble stack. We can read NRF_LOGS. However when we test with the ble_app_blinky that works fine with...
We have been using gpiote low_accuracy port events on battery powered devices for years without any issues, but now we bumped into a strange issue.
Details: 8 PORT (hi_accuracy...
