Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I want to encrypt the BLE data.
If I understand it right the cryptocell can't encrypt the data sent over BLE automatically, instead the application has to encrypt...
Hi, I am working on sample projects on the subject "proprietary_rf" which includes the nRF5_SDK_15.2.0_9412b96 sdk. I updated the codes according to my own project. Finally...
I TRY TO PROCESS OTA FROM SDK11 TO SDK13, BUT ITS NOT WORK.
WHEN I SEND THE ZIP FILES, IT WILL CLOSE OUT FROM BOOTLOADER.
SO HOW DO I PACKAGE THE ZIP FILES?
Hi,
We are building an application where we want to use BT 4.0 legacy to advertise two advertising sets at different time intervals. I just saw this commit in Zephyr repository...
Hi,
I am trying to develop the DFU capability for my device.
I added the necessary code from the example ble_app_buttonless_dfu to my application.
then started as explained...
Hi
I have developed a code on Windows using the Segger IDE.
I'm looking for a solution to build an the firmware on the Linux VM to automate the build process to generate...
Hi, I am trying to create DFU for nRF52 devices using NCS now that they are supported. I have done this previously with nRF5 SDK and it worked great. Now I do not see any...
Hi,
I have implemented ias serive with nRF51 and SDK 12.3, but not generating any ble event with IAS service. The code is working fine when compiled in a different machine...
I have two nrf52 boards I have dumped spi and spis program in them.
When I transfer data from one board to another i get noise
For example if i send "123" from master...
Hello,
For SI- and PI-Intigrity Simulation issues I need the IBIS-Model of the nRF52840. Is there existing IBIS Model for this component. When yes, then where can I get...
Whether BLE 5.0 support for audio stream? Also, I want know it is possible to connect 2 headsets+2 TPMS device+1 Phone with a single device at same time? And it shall able...
Hi,
we ordered by Data I/O the Algorithm for the device NRF52833-CJAA-R
For this we need a documentation (datasheet) including the CSP-Package (CJ) with pin-description...
Hi All, New user here but couldn't find a concrete answer to the following question. In PIC land I've usually allocated fixed memory using the _at_ or __attribute__ label...
Hi. I have a problem with my NRF52840 Dongle. When using BSP driven button. I've tried to use some SDK precompiled examples - it doesn't work. Neither with ble_peripheral...
Hello,
I am trying to add application specific errors codes to the error handling framework in the nRF51K SDK. The documentation in sdk_errors.h says that a range is reserved...
