Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I´m using the NRF52810 device and have an issue with the SAADC peripheral.
I basically have 2 channel where i want to do some averaging to improve noise.
The setup...
Hi,
I was exploring TWI master with TWIS Slave example in SDK16.0.0.
It works for sequential reads in loop-back mode.
Now I connected the simulated eeprom slave...
hi, I set up the environment according to the nrf_sniffer_for_bluetooth_le_3.0.0_129d2b3 file downloaded from the official website of nordic, the operating environment is...
Dear Nordic Team,
we have unstable communication with an Osram BT device through nRF52840. We got information from Osram developers the nRF52840 is the right device for...
Hello!
I have question about Direction Finding in nRF52811, Angle-of-arrival to be exact.
To begin with, I have a custom board with nrf52811 onboard and 8 antennas....
Hi
As far as I know, NFC supports peer-to-peer communication, so I want to know whether peer-to-peer communication can be achieved between two 52832 through NFC? Is there...
Hello everyone.
Iam working on a project where i need to detect a falling edge from a ADC (ADS1298) when new data is ready at a sample rate of 500SPS. I have the issue...
Hi Great Nordic Support Teams:
I'd like to know schedule of nrf9160 specification:
1.When will 9160 support R14 regulation in NB-IOT/ LTE ?
2.When will Nordic release...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
1) I ported UART into my code and it...
Hey all,
I would like to make a flexible design with ability to assemble NRF52832 or NRF52810 , both are pin to pin compatible ,
But i just wonder how to consider regulation...
Hello,
I am developing a capacitive sensing application with the nRF52 DK and Segger Embedded Studio. So far I have integrated the Capacitive Sensor Library Example into...
Hi everyone,
I am working on a project with the NRF9160 DK where I want to use the UART3 channel.
The issue is that I got compiling errors when I add CONFIG_UART_3_NRF_UARTE...
Hello,
I want to test the Thingy Mesh Provisioning Demo v0.7 with the codes provided on the GitHub:
https://github.com/NordicPlayground/thingy52-mesh-provisioning-demo...
Hi,
I am using s140 v7.0.1 for nRF52840.
I found if I configure NRF_GPIOTE->CONFIG[0], then BLE will not work.
Which GPIOTE channels are used in s140?
Thank you.
