I'm building a project where I need to sniff bluetooth data exchanged between a Voltcraft SEM6000BT plug and my phone app. The idea here is to capture the BTATT (where the...
Can you clarify, is it possible for the nPM2100 to set Vout < Vbat I.e. 1.8v out with 3v battery? The behaviour of the EV kit suggests not...
The datasheet isn't really...
We are building project with this config parameters: But we get this error messages while compile: If we use CONFIG_LOG =n for mcuboot, then project compiles normally. Also...
I'm developing a solution using the nRF9160 and would like to confirm the correct method to completely disable NB-IoT mode so the device operates exclusively in LTE-M.
...
Hello Nordic team, We are trying to use ST7305 display (custom driver that we have developed using st7789V as refrence ) and acconeer A121 senors on same SPI bus. The A121...
Hello, as from title, after updating from ncs 2.7.0 to 3.0.2 my application cannot advertise and scan concurrently anymore.
If I start advertising after starting a scan...
Hello,
I am using the NRF54L15 DK for development. I have configured the i2c with P1.12 as SCL and P1.14 as SDA.
below is my code in .overlay file
Below is the code...
Hi,
I am fairly new to this, so please excuse my beginner mistakes.
I have a few coin battery sized nRF51 beacons (like this https://forum.mysensors.org/topic/6951/nrf5...
Hi teams,
I want to find GAP address of sending node after received message.
In client model callback, there is access_message_rx_meta_t argument, and I can get unicast...
I am using an nRF520 PCA10040 dev board with a nRF52832 module and I am trying to get the ble_app_uart_pca10040_s132 FW to run using the SES segger tool set. After about 1...
Still having trouble getting a simple Blinky example running on two nRF52840 DK boards configured for a long range PHY_CODED connection.
I've looked through this post -...
I am new to the Nordic SDK and Segger embedded studio, and I am trying to test my NRF52840 dev board.
I am running the "ble_app_blinky_pca10056_s140" example, and I want...
1. Background info
We're developing a new IDE for microcontrollers (see https://embeetle.com ) and would like to support a range of Nordic Semiconductor microcontrollers...
1. Intro
We're developing a new IDE for microcontrollers (see https://embeetle.com ) and would like to support a range of Nordic Semiconductor microcontrollers. We received...
Hi,
In case of nRF52810, is it possible to implement both Master and Slave Mode ?
Also, this has do be done while the product being able to work with AT Commands.
...
Power Profiler V2.3.1
Hi,
I recently started doing power testing on one of our boards using the power profiler kit. I wanted to tested current consumption at different...
Hi Nordic Community,
I am trying to build a network using the OpenThread protocol and the nRF52840 chip. I have several Dongles, but I can't figure out how to flash the...
I'm importing ble_app_blinky_pca10040_s132 example in segger IDE. I'm using EVK-NINA-B1 and from nRF SDK I'm trying to importing example but getting error as mentioned in...
I have an external clock running at 3Mhz which I'd like to align with in software. Consider this contrived example:
What would the consequences be of attempting to read...
Hi,
I'm very new to c programming and your hardware. Please excuse my novice questions.
I'm making a rotary braille display using nRF52840 dongle (PCA10059) as it's brain...
Hi,
I using custom nrf52840 board .I have loaded the Bluetooth program in to the custom board using swdio/swclk/vtg/gnddetect these lines.There is no problem in Bluetooth...
I'm attempting to get MMD set up in an IAR project following this tutorial: https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/monitor-mode-debugging---revolutionize...
