When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been trying to get UART working properly on my custom board but also on nRF9160 DK. I'm using only UART_0.
With CONFIG_USE_AT_HOST and without any uart code...
tag v1.1.0 (have done west update) using SES 4.30c as suggested by nrf connect Compiled and flashed using SES modem firmware mfw_nrf9160_1.1.1 downloaded and updated the certificate...
I have developed a ble5 long range and meshing product but my life is way to short. using 2-3.6v batteries in parallel and only getting 2 months life in my battery calculations...
Hello everyone !!
While in test, I use Phone Mi Max 2 communicate with NRF52, sometime NRF52 send to Phone but Phone didn't received. I used sniffer and see packets to be...
Hi !
We are planning to add sensor device over Mesh network.
This sensor device will share Room Temperature, Outside Temperature, Humidity, ambient light and movement...
Hi,
I am working on BLE project which has 2 custom services with characteristics values having properties as READ/WRITE and NOTIFY.
Now when I enabled NRF_LOG through...
Hi Nordic,
I created a BLE custom service and now i want to merge this in Light Switch(Mesh SDK version 2.2.0) example from here.
I already kept the custom service code...
Hi everyone,
I recently finished developing a program that includes BLE, mesh and DFU.
Everything seems to be working but there is a problem with disconnection.
The...
Hi Devzone!
The development is in the final stage and is now testing by connecting the dc adapter or battery, not by connecting the pc cable and the debugger. However...
To get the reason for the restart, I called the sd_power_reset_reason_get () function after the ble_stack_init () function in main, but there was a problem. The return value...
Hi,
I'm developing a project which use softdevice and some peripherals together. I want to use serial communication with uart. But i couldn't initialize the app_uart module...
Hi there, Im successfully sending 1.1mB om data from Android Samsung S9 or iPhone 11 Pro. My problem is the low throughput i achieve, its about 6.1kB/s on iPhone and about...
Hi
I have a few questions as a newbee on Nordi products:
Can nRF9160 be used as modem via UART in the same way as i.e. Simcom's ?
Is it possible to run code on the...
nrf_log_push is declared as
I think the const in the parameter should be before the pointer not after it? const-qualifying a parameter (as opposed to the chars pointed...
I am developing a device based on nrf52840, this is peripheral. But I want to change the code so that I can only connect to my device using my application (in other cases...
