I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi,
I'm using an nrf52840 dk to query another device over spi and then pipe the response back USB to a host PC. Ideally, we're piping data at 1 Mbps (which should be very...
Hi,
We are using nRF9160 DK. Loaded the asset tracking application, and followed all the procedure to connect to nRF cloud.
In nRF cloud i can see the data in the cloud...
Hello,
I am currently designing a custom PCB with the nRF8001 chip. For a smoother assembly and component procurement, I am looking to make all the resistors on the board...
Hi there,
I have a problem with the bootloader from the RF5_SDK_11.0.0_89a8197 together with Intel Wireless Bluetooth chipset.
I use the softdevice s132_nrf52_2.0..1. I have...
Hi im after the library driver for the nRF509 using Arduino but when i go to the webpage to get it the webpage says not available can someone advise please
Many thanks ...
Hello,
Is it correct, that periodic advertising is working only with non-connectable mode? To implement periodic advertising with connected mode I need to start the second...
Hi, I tested a simple client-server UDP application, using as a template the UDP examples from the SDK. The UDP server is running in a nRF52 board and the client is a Python...
Hi,
my goal is to send data to the Google Cloud Platform using CoAP.
I found this example:
https://infocenter.nordicsemi.com/topic/sdk_tz_v3.1.0/thread_google_iot_coap...
Hi,
Recently I have been working on nrf9160 and wanted it to work as a modem for a linux computer for example raspberry pi. The aim here is that I connect the nrf9160 to...
Hi,
We are using nRF9160 DK. On the Arduino connector, we connected STM X-Nucleo-IKS01A2 sensor shield. We wanted to fetch the sensor values using nRF9160.
What example...
Dear Sirs, good night
Currently developing hardware using nRF52840 based module (BT840X from Fanstel)
Wanted to ask if following assignment would be OK for controlling...
I would like to know What is the limit on the number of ble devices that can be tracked concurrently by one Nrf52833 acting as an AoA device?.
Is there any reference antenna...
When I migrated the official routine pwr_mgmt, the following warning occurred after the compilation was complete. The files were all the same, but why didn't the official...
When I migrated the official routine pwr_mgmt, the following warning occurred after the compilation was complete. The files were all the same, but why didn't the official...
