I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Dear,
We just start to development our project. I use the Segger + nrf5_SDK_for_Mesh_v4.0.0.
I open the light switch sample project from "nrf5_SDK_for_Mesh_v4.0.0" by...
HI,
I am working on the interface between the nrf52832 and the MPU9250 IMU.
I have communication working fine with using nrfx_twi, but I have the following error when...
Hi,
I'm writting a simple test code that uses the aplication timer library (app_timer) to wake up from SystemON Idle mode to SystemOn mode every 1 minute. The idea is to...
Hi All,
I wan't to have logging via segger RTT from enabled modules in the MESH SDK.
Tried several config options in sdk_config.h, but without luck.
I made a diff of...
I'm using the app_timer library to create one shot timer. I'm calling the app_timer_start() to the same timer repeatedly in the gpiote handler. I had thought that this would...
Hi ... i want central to connect to the two different peripheral mac address , i am using ble_app_uart_c example version 15.2 .. using scan_filter_address i can abe to connect...
We are using the soft device (s140) in SDK version 16, our device is configured as a peripheral.
I have a program that connects to and then immediately disconnects from...
To the kind attention of Nordic support team,
using these commands, like in https://devzone.nordicsemi.com/f/nordic-q-a/58365/doing-dfu-ble-as-a-pca10059-dongle ,
I flashed...
To the kind attention of Nordic support team,
I'm using a command like this: nrfutil dfu usb-serial -pkg x.zip -p COMx.
I use it to program a default PCA10056 DK board...
I have system on sleep mode implemented which is still drawing 8mA of current i would like to take it down to 1mA or less what i need to do to get it that low?
I have two...
Hi, I'm currently trying to build a provisioner using pyaci and an nrf52 DK: pyaci provisioner
but I end up with these errors every time:
I tried on windows 10, ubuntu...
I noticed a bug in ble_cts_c. The BLE_CTS_C_EVT_DISCOVERY_FAILED event is sent to the event handler for every UUID registered for discovery. The BLE_CTS_C_EVT_DISCOVERY_FAILED...
I am making HID composite devices, but I find that if the number of report ids is more than 5, I cannot send data from PC to this device；Error code 1784 is displayed
If...
Now I'm developping a USB MSC project, the Nand flash size is 4GB, I don't know how to set USB capaticy size.
I change the setting in nrf_serial_flash_params.c:
static...
