Hello everyone,
I'm reaching out to this forum in a bit of a bind and hoping someone might be able to offer some guidance or assistance.
I'm trying to download the S340...
Hello LE-Audio team,
By any chance, do you have a working code base that supports a headset with 2 end points instead of just one as your sample nRF5340_Audio kit?
If...
Hi, I just tried to connect LSM6DSV IMU with nRF52840dk
The whole folder structure is shown below :
1. I set nrf52840dk_nrf52840.overlay file first.
2. I...
Hello,
We are designing a new Zigbee/Thread end-device sensor and I'm wondering what is the recommended part for it.
I have a demo running with nRF5340 (because the platform...
Hi Nordic team,
I'm using the nPM2100 PMIC in my design to power a microcontroller. The microcontroller sets the nPM2100 into Hibernate mode , and a vibration sensor connected...
Hello,
We are currently using the nrf52840 for development using Zephyr v3.7.99-ncs1 .
We want to use the UART in low power mode and therefore, we have used the zephyr...
My attempts to configure the Zephyr device tree to run littlefs on an external SD card have repeatedly resulted in what appears to be the creation of a small littlefs instance...
I searched over the website, I couldn't find a good introductory documentation for programming the nrf51822, specifically the nrf51-dk. I have a transistor hooked to p0.01...
Hi Team,
Is it possible to have multiple profiles like serial, heart rate monitor, proximity etc. in single code?
What are the efficient ways to do it?
Regards,
M...
Hi,
I'v a query regarding the two development boards PCA10001 & PCA10028.
I have worked on a project with development kit PCA10001 and made the release to customer ...
I have followed the instructions and have tried with s110 6.0.0 and SDK 5.2. I can compile and download to the board but can never detect under discoverable device onn MCP...
I am running ble_app_uart in my pca10004 board. The crystal configuration is set to 32khz crystal.
But i want to use the 16mhz external crystal for my use ,because my application...
Hi!
(I moved this question to the "Questions" area from another area.)
I am using Eclipse to develop and debug on nRF51 DMs (PCA 10028). I have managed to run and debog...
Dears,
Just one question for RTC.
In SDK9.0, it's possible to control of time to use HW RTC block??
If possible, please let me know how to use it..
Thank you.
Lets say I have 200 bytes of data that I want to store in flash. So, I request a 200-byte block.
In order to store, the area has to be cleared first. As far as I understand...
Using the nRF51-multi-role-conn-observer-advertiser-master project to test timeslotting I have encountered two issues (Softdevice s110 7.1)
Issue #1: Repetition of advertisement...
Now, I need two function add my project (On BLE stack).
Distinguish long/short press at same button.
2.device and master synchronous time.
No.1 question is...
Hi
We have custom nrf51822 board.
in that we have nor flash which is spi compatible.
so in order to read device id i used spi_master sample source code.
i am able...
Hello,
I'll explain my code:
NRF51 takes samples of a sensor every 10 minutes. In addition, softdevice S110 is used... An user can connect at any time, so advertising...
I am trying to implement frequency counting on nRF51822 by counting number of pulses in a given period. I create a PPI channel with a GPIOTE event on rising edge linked to...
Hi,
is it possible to mount a nRF51822 in an aluminum enclosure and use ble?
I am looking for a range of up to ten meters in an open area.
Is that possible or will the...
