Is there an AT command (For modem firmware >= 2.0.2) that can be used to validate whether the LTE modem can communicate with an external MIPI RFFE switch (for example on a...
Can Nordic share specific instructions on how to enable hardware tracing?
I've received the following patch from Tomasz, however I still see "trace clock missing" in Ozone...
Hi
our last product is based on nRF5340 and now we start a new design based on nRF54H20, and its essential for our design, i checked alot but there is no datasheet, reference...
NCS currently has a nice feature where the firmware versions are printed in the boot banner:
Is there a config option to also enable printing the nRF91 modem firmware...
Dear all,
after cutting the SB bridge to the QSPI chip and close the ones to get the pin free and disabled also qspi inside the nRF52840dk_nrf52840.overlay file I'm unable...
Dear all,
I stubled upon the following issue when developing a BLE sensor product. When I try to bt_gatt_notify(); With only one characteristic, there is not an issue...
I was looking into the sdk provided by nordic for nrd52840Dk board and want to test the zigbee protocol. I havn't find any sdk for that.
Can you share me some links and...
Hi,
for our prototyp we use a NRF52. When i flash the device, it will always be go in sleep mode after a duration of time and stay in there.
Is there an interrupt which...
Hi all,
i am using V11 sdk.
i want to send data "hello" in beacon application.
how to add that feature.?
any function calls are there?
-Thanks in advance
Hi,
I am using a PIC microcontroller in my project (18F family) and I would like to know which are the tools needed to begin development with the NRF80001.
I already...
Hello,
I am doing a project using nRF51822, s130 and SDK 11. I have modified the example ble_ap_hrs_rscs_relay.
My problem comes when I try to update a notification...
Hi,
I am porting our application from SDK10 nrf51 to SDK12 nrf52. The application takes use of a serial console accessible over UART.
I notice the new logger module...
Hi all,
i am V11 sdk.
Task:
i want to send and receive data without connecting the nordic_uart example
i.e ble_uart eg is send and receiving the data when we press...
Hi all,
i am using V11 SDk,
my task:
One board should broadcast continusuly.
if there is any neighbour is broadcasting ....then that will capture those data too...
Hi,
I am working on adc module of nrf51,through adc i am taking data and storing it in array.now i have to crossexamine this adc data with the prestored data and have to...
We are trying to complete Bluetooth qualification on our Cycling Power Service (CPS) against the Bluetooth Test Specification (Document Number CPS.TS.1.1.1).
We fail the...
We have been working on a project that requires the following separate segments be programmed to the board:
softdevice hex file
app hex file
UICR hex file
...
Hello,
I'm currently porting all my C++ code from SD130 SDK10 to SD132 SDK12 and I also upgrading from device_manger to peer_manager.
I've noticed that in peer_manager_types...
Hello,
It seems that NRF_LOG_BACKEND_SERIAL_UART_BAUDRATE has wrong documentation. In sdk_config.h it says:
// <o> NRF_LOG_BACKEND_SERIAL_UART_BAUDRATE - Default Baudrate...
Dear Nordic Team,
Thanks for support.
I want to know the possible for nrf52832 act as a sniffer. If it is possible means i want to latest sniffer hex code.
Dear Nordic Team,
Thanks for support.
I have tested Current Time Profile sample application whenever connect with nRF connect APP the debug widows shows always "Current...
Good morning all,
We have a circuit based on 51822 chip.
We are currently trying to monitor some value from 0v to 24v from the analog inputs.
It's working, however...
