I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
My Setup: -> OpenWRT Chaos Calmer 15.05.1 -> Kernel - 3.18.23 -> MCU - nRF52832 Custom Board -> SDK - 15.0.0 -> IDE - Segger Embedded Studio
I am able to start a 6lowpan...
Hello,
I would like to know from were i can get release history for Nordic device family pack.
I can find Zip file for downloading different Nordic family packs but wit...
We want to support low power end device sleepy so do the MESH SDK 2.0.1 has the support of Friend and low power mode support in mesh SDK? I'm using nRF51822 SoC .
How are multiple messages to the same device/group/broadcast managed in Mesh?
I have a system where two switches control single light bulb. If both the switches try to turn...
Hi,
I am new in BLE.
Can anybody please explain me, how does tx_power_service works.
And how does it calculates the RSSI value.
Thanks in advance.
Varun
I am now based on nrf52832 SDK14.2 development, as a slave, when nrf52832 and mobile phone Bluetooth link, I want to know the current connection interval, how can I obtain...
I am interfacing LIS2DH with nrf51822. I am using 12.3.0 SDK and 130 V2 for development. I have successfully interfaced LIS2DH eval board with Nrf51822 eval board (waveshare...
I am using this flash data storage as reference github.com/.../nRF52-fds-example
Running fds_test_write() below, it writes to a file specified by FILE_ID, REC_KEY but to...
I recently got the Power Profiling Kit set up with the Power Profile 2.0.0 desktop software on OSX to measure current of my custom board. Sleep current for the whole board...
Hi,
In one of my application for Bluetooth 5.0 i would like to use nRF52840. Product requires certification. I would like to use MCU which has BLE on chip and certified...
Hi,
I'm using nrf523810. The current consumption that I get for proximity is 4mA and I want to reduce it to less than 1mA. I use the proximity example nrf5 sdk v14 and v15...
The computer and the 52832 are connected through a serial port. I want to send 2Kb data to my computer. But my computer can only receive 256b data. What should I do?
Hello,
I'm currently using the light switch proxy example with 3 server proxy, 1 client proxy and 1 provisionner.
The example is currently working but I don't understand...
Hi,
I have a question regarding the width of the RF traces on the NRF24L01+. From the gerbers I notice the width is approximately 0.5mm and the separation to the closest...
Hi every one.
I have issue that: our board production have NRF24L01+ IC not good, so we need replace them by new IC.
But we dont have enough NRF24L01+ IC, we have NRF24L01...
