Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
Hi,
I'm trying to use the HCI UART sample to provide Bluetooth support through UART. At first I want to test it between two Nordic Boards, but later switch to another MCU...
Hi,
Also asked your AI, but if I combine the information on https://docs.nordicsemi.com/bundle/ug_ppk2/page/UG/ppk/measure_current_source_meter.html with that on https:...
Hello Community!
I want to use the npM1100 as a power management device in my project. The external battery to be used is the ER26500 and it is not rechargeable.
If I...
Hi,
We have a product in production which uses the mpsl_radio_notification_cfg_set() function along with a callback to control an external GPIO when thre is radio activity...
Hello, I have a question about how to monitor Zigbee devices for dead or alive, especially end devices that sleep. I am currently developing a hub to control and retrieve...
Hello, We have a custom board with nRF52832, using BLE, s132. I have noticed recently that in nRF Connect App (v4.29.1) usually the services and characteristics show up twice...
Hi there,
I am trying to develop a simple application that must write information within a micro SD card (nothing too fancy, it is just plain data read from the internal...
Hi,
I added MCUboot and SMP BT Service to the OpenThread CLI routine to implement the device firmware upgrade function.
I found that after DFU is completed, the Thread...
If the lock's status changes while the device is powered off, causing a mismatch between the lock and the Apple Hub, how can I immediately update the status upon powering...
Hi!
I cannot get I2S echo sample to work on nrf54L15. Tried following overlay
build configuration nrf54l15pdk_nrf54l15_cpuapp
I verified with oscilloscope that no...
Hi,
All-of-a-sudden I'm having problems debugging my application. THis morning it was working right, this afternoon it's gone wrong!
I think it's pretty near using up...
Hello,
we want to get three different states using only one GPIO:
1. nRF52840 GPIO output driven low
2. nRF52840 GPIO output driven high (3V3)
3. nRF52840 GPIO internal...
Hello Nordic community,
I'm working on a project using the nRF5340DK where I need to achieve precise control over three GPIOs with the following specifications:
P0.07...
Hello,
We are using the nRF52840 on our own board.
When I added up the current consumption at 3V, based on the datasheet, I get 14.3mA (CPU from RAM, Tx at 0dBm 1Mbps...
