Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello,
After having read the documentation of "nRF5 SDK v15" and "nRF5 SDK for Mesh v2.0.1" it is not clear to me which PHY layer it uses at the end.
In the documentation...
Hello,
I am going to use nRF52832, but I have nRF52840 DK, can i use this bord for developing project on nRF52832. Is nRF52840 compatible with nRF52832 in software and hardware...
Hi
I assigned one LED Signal to P0.08 pin in nRF8122 CFAC package as per pin assignment it shows as digital GPIO
But in Firware wise when checking the LED Does not glow...
Dear all,
maybe I‘m missing something, but I know there are OTA DFU client libraries for Swift, ObjC, Java and Python.
But it looks like there is no DFU lib from one...
I was using nrf51822 ,S110 and SDKV10 i had created custom services and its working fine, But when moved to nrf52 DK and S132v5 SoftDevices and SDK version 14.2.0 . same services...
I would like to develop some app to be able to use nRF51 dongle on PC. Is there any good example codes to start with? My plan is to use pc-ble-driver-js and Electron and found...
Hi,
I am starting to look at using 2Mbps Phy (and eventually coded PHY). I'd like to add the functionality where my device will automatically switch PHYs based on some metric...
/**@brief Function for finding out whether a peer ID is in use.
*
* @param[in] peer_id The peer ID to inquire about.
*
* @retval true peer_id is in use.
* @retval...
Hello tech support!
I am using the built-in SPI to transfer the data. Also, I adopted the "timer" example in the SDK for handling the SPI transfer.
However, it seems that...
hi
I want to design Nodes for asset tracking. These Nodes will be spread out in a building. A moving object will have a BLE -Advertosor. The Nodes will detect Moving object...
Hello, I'm using the nRF51822_QFAA chip on a pca20006 board. I downloaded sample code from the offical site. Installed sample code nRF51822_beacon_firmware_1.1.1.msi. I use...
SDK: 14.2
64-bit Segger Studio 3.34b
PCA10040 Rev. 1.2.4.
64bit Windows 10
SD: S332
I'm trying to add the bpwr Tx profile to the ble_ant_app_hrm_pca10040_S332...
Hello fellows,
I did my master's thesis with the nrf51 and now some years later I need some help setting up a Laird BL652 to work with my beloved NRF+Keil tools.
Here...
