Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hello Nordic, I'm reading: creating new modes in sdk documentation. In the simple_on_off client model, I do not understand the place I underlined in the picture. When is the...
Hi,
I'm looking at prototyping something for very small volume and looking to go the 3rd party module route ( www.nordicsemi.com/.../3rd-Party-Bluetooth-Smart-Modules)...
Hi,
I'm trying to capture Mesh packets using nRF Sniffer 2.0.0 and nRF52 DK while running the Light switch demo, but so far I haven't been able to capture any packet that...
Hi,
I'm having an issue when responding to rw_auth requests on the nrf52840 w/ sdk 15.0. When I'm attempting to update the table, If I make the length too large then it...
Good afternoon,
We just migrated our peripheral application, working perfectly on the nRF52840 DK, with SDK15.0.0 and SoftDevice6.0.0, and it is now crashing with SDK15...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
Hi,
I have tried the following example: infocenter.nordicsemi.com/index.jsp
Everything works fine (I can generate a notification via a calendar event and see it via the...
I get NRF_ERROR_INVALID_PARAM when calling sd_ble_gatts_characteristic_add(); If I comment custom service initialization where is this function I get the same error NRF_ERROR_INVALID_PARAM...
Hi, For a new project we need a smaller devices compared to to the nRF52832 dev board but still want to stay with the nRF52832 chip without making our own PCB. As an alternative...
We have a large number of units in the field running on SDK 13.0.0/S132 SD 4.0.3 and in order to add new functionality we need to migrate to SDK 14.2.0/S132 SD 5.0.0 via DFU...
Hi,
This is a follow up of issue: https://devzone.nordicsemi.com/f/nordic-q-a/28211/thread-dfu-upgrade-problems/111436
We're trying to perform DFU by following "Thread...
nRF52810 only supports S112 so the max throughtput anyone can achieve is 330 kbps .. please provide proof.. test data. Only nordic employee please answer this or someone who...
