Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
Hi Support Team,
I tried several ways to set the image version but failed. My SDK is ncs V2.5.2. 1. set(CONFIG_MCUBOOT_IMAGE_VERSION "1.0.0") in CMakeLists.txt: did not...
Recently I've had an issue with 3 of our nRF9160 based products during production (several hundred of the same hardware/firmware/SIMs work fine). The issue is that while the...
Hello Nordic support,
My application is a Zigbee coordinator application on nrf52840 based on nRF5 SDK for Thread and Zigbee v4.2.0. I was able to pair a Zigbee end device...
I am using the Zephyr SPI driver to control a WS2812 LED strip through the SPI interface. Since only the MOSI line is required for communication, I want to configure the SPI...
I am developing a device that uses ESB.
Uses modules that are Telec and FCC certified with BLE profiles. (module : MDBT50Q-512K)
I have a few questions.
Q1. The TX power...
I have two boards:
nRF52840 DK (which has a faulty buck converter, so I am powering it via USB).
Fanstel BT840F board , which provides power to the Debug In connector...
I used nrf5340 on my board and did some changes based on audio demo.
Unfortunate,I heard a noise after set configure like bis gateway, audio input from usb ,48k 16bit 2channel...
Hi,
I have a problem with unmodified BLE Shell and changing security level to 2(aka just works).
1. I'm connecting from BLE Shell to the device that requires level 2 2...
I am attaching an adapter board to the nRF52840DK to debug a custom board.
However, if there is any contact failure on the adapter board, the nRF52 on the DK will be the...
Hi Support Team
1) Does the new nRF54L05 chipset need to recover before program? We execute command line nrfjprog --recover but it is unavailable for nRF54L05. And nRF54L05...
Hello,
I am developing matter sensor and I would like to send data to `MeasuredValue` attribute of `CarbonDioxideConcentrationMeasurement` cluster. I followed this tutorial...
I have an nRF54L15DK and a custom-designed nRF54L15 board. These two boards use different pins for peripherals. The NCS version used is v2.9.0. I compiled a Matter project...
Hello, Not sure if this is the place for these questions, but here it is:
I've configured new board, and when I try to debug using the ncsconnect vscode plugin (linux...
