I have used your example of a bootloader nAN_18. I can create a basic program, with new firmware, and also load my new bootloader program at the high end of memory.
My...
Hi,
I'm developing some projects with the nRF51822 chip and I am not able to debug them successfully any more. However, I have previously debugged correctly some projects...
Hi,
We've been seeing an intermittent connectivity issue in Yosemite in discovering BLE services, namely scanForPeripheralsWithServices does not return anything. The same...
Hi there is a problem in github.com/.../nrf51-UART-examples
any one can help?
I put empty loop in main, and comment off all ble related int. and I process uart_evt by...
Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
Hello guys.
I'm new with nodic nRF52 SDK and I tried to enable debug by setting 1 on "NRF_LOG_ENABLED" in sdk_config.h, but nothing happens in com port criated by Jtag...
Custom app running on a nRF52 devboard. Serial port runs when I use the debugger and continues after I exit the debugger, but does not run from a cold start.
using the...
Hi,
In nRF5 SDK v12.3, the members of nrf_ecb_hal_data_block_t are pointers to non-const data. I was wondering if these indeed need to be non-const for the Softdevice S132...
Hi,
I have a central and peripheral device both are based on nRF52. Central device is running on SDK 12.2.0 and peripheral with SDK 11.0.0. I would like encrypt the communication...
Hello!
We're using SDK 12.3 on our application, and we're aware that the SDK is targeted to be event driven, meaning that our code should be the one keeping track of the...
I am using SDK15 , nRF52832 custom board , keil uVISION 5 , ble_app_beacon example.
I am adding timer to the example.
In below code, when I comment out update_vbatt()...
Good afternoon,
I am facing the following issue:
a client application writes to several characteristics (write with no response) I set in my chip, which trigger the execution...
Hello,
We are porting legacy application to the nrf52840. We are using Keil uVision 5.
The legacy code is using some gcc ideas and extensions so we are forced to use...
Hi ， All
I am using nrf52832 SDK12.3.
When the host runs to the discovery service but has not yet discovered the service，the slave power off. The host can no longer connect...
Hi there.
I Tested Example (secure_dfu_ble_s132_pca10040). Fine work.
but I could not find the example code to transfer the firmware.
I need the code to receive...
Hello,
I'm a little bit confused about max datalength that can be read/written in a characteristic.
See attached, a MTU of 64 bytes is negotiated thus 61 bytes available...
hello there! I am working on a project in which two devices(one is central and other is peripheral ) uses Nordic bluetooth controller nRF51822 for connection and data exchange...
I uploaded a sample code into an external nrf51822 module using nrf51-dk as explained by this blog www.instructables.com/.../ . power supply for the external module was from...
Hi
The following ticket explains when I configure pin21 as RESET it will be hardware configured to pull-up internally. https://devzone.nordicsemi.com/f/nordic-q-a/8342/nrf52832...
Hi all,s
I have a couple of nrf52840 boards and i was testing the ble mesh light application. The application works fine, but i changed it so it will periodically set...
