I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
SDK: 3.0, nRF54L15
I have modified the clusters using ZAP tool (west zap-gui). When I tried to built, I get the below error:
1. I used Matter door lock sample and the...
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hello,
We are currently using the nrf52840 for development using Zephyr v3.7.99-ncs1 .
We want to use the UART in low power mode and therefore, we have used the zephyr...
Hi,
Now, I'm doing a project. A device node sends picture data and the other one receives these data. Then the receiver shows the picture on the SSD1306 display.
At receiver...
We need to measure the RF power(continuous unmodulated signal) of our custom board based on nrf5340 using spectrum analyzer. please suggest the steps and tools to perform...
Hi
When i used for DK nRF54L15, PMIC nPM1300 was burnout.
and this PMIC i want to directly replace the DK with a new npm1300.
Can the software that comes with this...
Hi,
I am facing issues while setting up the PPK2 in one of my desktop.
The same hardware is working fine on another desktop.
Can you let me know what could be missing...
I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
Hello,
I'm trying to make the nrf5340-DK capable of connecting to BLE from multiple devices.
The program is based on: Bluetooth: Bluetooth: Peripheral UART .
I found...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hello,
I am having nRF9160 with modem FW = 1.3.6 and nrf sdk version 2.7.0
I am using MBEDTLS library for generating self-signed & CSR certificates with EC-Key and RSA...
Hi,
I bought a new nrf52840 DK board as one ofthe original nrf board of my Qorvo QM33120WDK1 kit ( 2 x nrf52840 DK + QM33120W + QM33110W) J3 connector broke. Out of the...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi everyone.
I cutted PCB track shorting solder bridge SB40 .
I connected like this..
Then I opened power profile kit 2. I am using amperemeter..This is my app scrrenshot...
