We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
I am using Zephyr 2.9.0 with the sdk-nrf repo v2.9-branch checked out. The locator_tag sample builds without issue and flashes to the nRF54L15-PDK without issue. I have a...
I'm trying to use raw packet transmission (IN combination with wifi promiscous mode and raw sockets eventually) with my nRF WiFi device. I have both the sample raw_tx_packet...
Dear DevZone,
I would appreciate your assistance in understanding how to correctly configure Wi-Fi and BLE coexistence for the nRF5340DK and nRF7002EK with SDK version 2...
Hi! I'm testing the application with the custom Battery pofile I generated with nPM PowerUP app. During testing I found the issue with the SOC value calcultation depending...
Hi Nordic Team,
I am planning to develop a SmokeCo device using the nRF54L15. I tested the example code of Smoke-Co from nrf-sdk with nRF54L15-DK and that working correctly...
Is there a trick to getting nrf_dm to compile on the nrf54l15?
I've installed v2.9.1
Command I normally use (nrf52840):
west build -b nrf52840dk_nrf52840 -d build_nrf52840dk_nrf52840...
Hello,
I am using the following device and development kit:
Device: NORA-B106-00B (nRF5340)
nRF Connect SDK: 2.0.2
Currently, I am trying to use GPIOTE PORT...
I've been trying to run the example Mesh/Chat on NRF7002DK, and the terminal print <err> bt_mesh_pb_adv: Failed enabling advertiser and <err> bt_mesh_pb_gatt: Failed enabling...
After using the backup v2.9.0 project to overwrite the original project, I encountered the following issues during compilation： How to solve it? Using Windows not Linux. Thank...
Hi Devzone
We found that the NRF54L dk will stuck if add systemView function into the bluetooth sample project
we add below config into peripheral_uart/peripheral_lbs...
i brought Power profiler kit II deveice and try to measure current on it.
i couldnt get proper measurement can you please help me on this? it is giving some random value...
Hi!
I have an NRF9151LACA AEA device and I'm trying to get it to work. Got the IMEI and the device successfully connects to cellular network.
However, I can't get HTTPS...
I am developing an app for a custom nRF52840 board. I am using the latest version of the nRF Connect SDK (2.9.1) and have enabled OTA DFU in firmware using MCUboot and sysbuild...
Dear Nordic Support Team,
I am working with the nRF52840 in a multi-protocol setup and would like to clarify the feasibility of the following configuration:
Running Thread...
