We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi All,
I came across this thread regarding programming external boards. ( https://devzone.nordicsemi.com/f/nordic-q-a/14058/external-programming-using-nrf52-dk )
In order...
Hello,Nordic team
I am programming with nrf52833 and ncs v2.9.0
While bonding with peripheral ,central report No memory to create new report.But my soc flash and ram are...
I work on nRF54L15DK.
When building for the nRF54L15DK, only 188KB of SRAM is allocated. The remaining 68KB seems to be allocated to the FLPR MCU. How can I change this...
Hi,
I recently bought a J-Link Mini EDU and a Tag-Connect TC2050-IDC cable (bought the legged version for some reason, but I guess I can break the legs). I wanted to use...
Hi,
I have one application that includes one basic BLE services such as one Custom service, ANCS, DFU and NUS.
I have a custom board with three i2c sensors, and one SPI...
Hello and thank you for your time,
We have created a board using the nRF54l15 and have used P2.07 & P2.08 for UARTE21 and P2.00 to P2.05 for SPIM20.
UARTE21 and SPIM20...
Hello!
I've just come into contact with the nrf54l15. On the customer's board, it is necessary to change the NFC pin to a regular gpio, and they following the previous nrf52...
How can the HFXO be selected on the nRF5340 NET Core?
We need to set the high frequency oscillator in the net core of an nRF5340 to use the external 32 MHz crystal oscillator...
Hello Team, We are currently working on implementing a multilink connection setup using the nRF52832 and nRF5 SDK v15.0.0 for testing purposes. In this setup, we are using...
Hello Team,
We want to interface USB pendrive to NRF52833 and it will act as USB mass storage, where we can read and write data.
Is this possible and could please provide...
Hello,
This PR was closed without action:
https://github.com/nrfconnect/sdk-nrf/pull/16889
It says " you can always re-open " but the creator (my colleague) was unable...
Hello Team,
We are currently working with the nRF54L05 SoC and are in the process of enabling DFU over BLE. However, after integrating DFU support, we are encountering memory...
Hello,I tyed to install the CMSIS Wirzard in SES on the video from https://www.youtube.com/watch?v=b0MxWaAjMco But it deosn't work. I don't know why. I did read the DevZone...
We use an nRF52832 analog input to measure the voltage on a large capacitor. I think we have destroyed some chips when the capacitor is still charged and the power to the...
Hi,
I'm developing an application on the nRF54L15 and recently I designed a custom PCB with a sensor that gives interrupts when its FIFO is full (should be around every...
