Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hello,
I am trying to play the AT45 DataFlash driver by directly copying the sample code from nRF connect SDK v2.9.1 (C:\ncs\v2.9.1\zephyr\samples\drivers\spi_flash_at45...
Hello,
i have one PPK2. Recently i find the current reading from PPK2 is relatively large compared with actual current value.
For example, actual current value vs PPK2...
I am currently working on creating a custom PCB which features an nRF9151 module. I am currently working on pin assignment for our peripherals. Given Zephyr uses a device...
Hello, we're currently developing BLE devices with PCA10040 and nRF Conenct SDK 2.9.0.
During a series of experiments, we found that with the same hardware and the same...
Hello,
I recently bought a Thingy91x; before that, I was using a Thingy91. I activated it and successfully programmed the Hello nRF Cloud firmware via the Quick Start in...
In NRF5 SDK17.1, I disabled the Bluetooth broadcast channels 38 and 39 by configuring channel_mask. However, when I measured the broadcast current waveform, I found that there...
I'm working on a IoT device that leverages the AWS IoT and AWS FOTA components from the nRF Connect SDK. The device is battery powered, and so I want to limit the connection...
Hi
I had a device that did not start up - because it was waiting for the 32KHz clock to be stable.
So I tried to change the setting below from 15pF to 5pF and it started...
Hi all,
lesson2, excercise2 is missing the code snippits.
Excercise1 and excercise3 do have code snippits to copy.
I tried on both Chrome as on Edge, but the snippits...
SOC: nrf52840
SDK: v2.9.0
Device is a central, it connected to 16 peripherals, these peripherals will power on 90 seconds and then power off 10 seconds(one cycle). ...
Hi,
I have successfully updated the firmware on the nRF5340DK controller using the DFU MCUBoot method. Now, I need to add Secure Boot NSIB to the bootloader and integrate...
I'm using ncs 2.9.0.
1. I flashed the firmware V0.15.1 on the device. And .
2. Update it "Confirm only" with nRF Connect Device Manager App to V0.15.2The update was Compelete...
I've recently encountered a problem where the Device Tree Visual Editor no longer displays any peripherals (ADC, UART, SPI), making them uneditable. I have had my own board...
Hello,
We use nrf54l15dk + MX25R8035F external flash to do the matter development on NCS2.9.0, and we meet some problems:
1. when the matter.ota is 1003KB, takes about...
Our design has an nRF5340 with RV3028C7 to provide the 32 kHz clock via P0.00.
If I configure P0.00 as a digital input, I can see the pin toggling.
However, if I use the...
