Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
Dear Nordic Technical Support,
I'm writing to report an issue I'm experiencing when trying to integrate MCUboot with a Zigbee R23 project for the nRF54L15 platform.
Issue...
Hi I am using an nRF54L15 with an external watch crystal. I have notice that depending on the manufacturer of the crystal I have to use a different internal load capacitor...
There are two USB ports. IMCU and nrf5340. I had a lot of trouble with bad cables but i found one that works and I find that I have a jlink drive that pops up so I know there...
Hello,
I have a custom PCB with the nRF5340 chip. I’m able to flash the board using a J-Link. I’d like to rename the device so that it advertises a specific Bluetooth name...
I am using the `mcumgr` subsys to enable the DFU (Device Firmware Update) capabilities in a custom device that also features a custom (non mcuboot) bootloader. In order to...
Is there any documentation on what peak data rates are available on the nRF9151?
While the Cat-M, Cat-NB1 and Cat-NB2 standard max data rates are easily available, I have...
Hi,
I have been playing around with the configs but I could not get Mode-3 to activate. What should I change for cs configs and the prj.conf file in order to activate it...
Hi Nordic,
I test with nRF7002-DK and IC mark on nRF7002 is below:
N7002 QFAAB0 2252AA
Here is my test data, showing about a 3dB discrepancy between power setting...
Hi, I just tried to connect LSM6DSV IMU with nRF52840dk
The whole folder structure is shown below :
1. I set nrf52840dk_nrf52840.overlay file first.
2. I...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I am working with the zephyr ZMS sample application. I am using SDK 2.9.0, and I built the application for the nRF54L15DK (nrf54l15dk/nrf54l15/cpuapp). The sample works...
Hello team, I am currently working on the distance measurement functionality using the development kit (nRF5340 and SDK: v2.9.0). At present, the distance measurement runs...
I am using the S312 protocol stack on nrf52810, with both BLE and ANT+enabled, to transmit heart rate. It can be used on most devices, but it is difficult to connect to 'wahoo...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi, I was using the BLE online power profiler to determine possible power savings with the nRF54L15DK over the nRF52840 using the zephyr bluetooth broadcaster sample. The...
