When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
We are a small start-up developing low volume product and paying 2500 USD to Bluetooth SIG for listing our BLE device in their EPL is too expensive for us. Is there any option...
I'm looking for a way to let my device "nrf51822" to be connected only to my own mobile app.
I'm wondring if you have already a Nordic solution that I can use ? (tutorial...
Hello friends,
I'm having MDBT40 EVB which is cheap one as compare to other but with lack of build and debug support. But i dont know how do i flash my hello world blinky...
developer.nordicsemi.com/.../a00935.html
The doc seems to provide only write functions.
And, the flashwrite example doesn't show how to read from flash even after device...
Hello,
I am currently looking through my error handling and noticed that there are some errors that I do not really understand fully, so I've summarized them here:
0xDEADBEEF...
Hi,
I am trying to make a communication between a nRF51(uESB) and a nRF24(ESB). The uESB uses tx_payload and rx_payload as buffer to send data. Bytes 0 to 4 are used for...
Dear Nordic team,
I've seen very much reproducible crashes of your Android nRF Master Control Panel app when trying to see details (button "MORE") of particular Peripheral...
Hi Nordic,
Is there a way to follow blog posts the same way as standard questions? I haven't found anything and it's really painful when you want to follow discussion or...
From bLE RF sniffer user guide:
To set up the Sniffer you will need one of the following pieces of hardware:
• nRF51822 Evaluation Kit (PCA10001) and a mini USB cable...
hi, i am a beginer in BEL application.
after some tries, i can compile and download 'ble_app_uart'.
but the module does not work at all also it dosen't advertising....
...
i make a new "Makefile! project" using example in SDK first i use the "blinky" ,
it looking likes can be work, then i try to use " blr_app_hrs_c " ,
i do the same step to...
I am trying to have the dk (i have the 10036 preview) send pwm signals to a motor controller so that i can direct its speed. I have based a lot of the code below of this utorial...
Hi, I have seen that on mbed compiler, there is a bootloader that include the DFU and with this, we should not implement DFU in application.
In keil, we must implement...
During Power Off mode the nRF52 GPIOs stay retained. But by waking up on a external Pin we can see another Pin toggles for approx. 600ns. It seems this happens during the...
Hi, all.
I'd like to broadcast only when i want to inform nortification.
flow like
No advertising when application start.
Check the events that there...
