When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
[nRF5_SDK_15.0.0_a53641a] is used. Please tell me how to select peripheral when connecting from central to peripheral. Since I want to connect to 4 peripherals for one central...
Hi to all,
i am developing a device with nrf51822 soc and i want use it as peripheral, in it have a characteristic that i want read it continuously from central. sometime...
I am using Hackable kit which is a custom nrf52832 board with Bumpy a low cost Black Magic Probe alternative to program since i don't have a J-Link device. I have tried many...
Actually, I am working on a IoT project in which tens of connectionless BLE beacons are broadcasting packets. Now, four Nordic devices(nRF52832) are receiving that data and...
I want to use the 2450AT42E010B chip antenna from Johanson Technology in my design. I selected this antenna specifically because i want to make a beacon using the nRF52832...
I want to build a device able to connect with smartphones and central modules preinstalled on the ecosystem.
Is possible to integrate Bluetooth mesh + Peripheral role in...
I have the nrf51 RADIO peripheral set up with the usual set of shortcuts:
NRF_RADIO->SHORTS = RADIO_SHORTS_READY_START_Msk | RADIO_SHORTS_END_DISABLE_Msk | RADIO_SHORTS_DISABLED_RXEN_Msk;...
Hi,
I'd like to be able to use an event from the LPCOMP to sample the RTC (either to a peripheral's register, or to a memory address), so I can measure pulse widths without...
I am able to initialize the module and get the callback , but when I try to write I will not get the callback after the write, and no errors.
If I simply try to read after...
Hi
I am integrating BLE with LESC into a legacy sensor product using SDK v11.
The problem I am running into are errors in the FDS module when trying to make a secure connection...
I use nrf52832 based on SDK14.2 as a slave development. Occasionally there will be a crash in the operation. The program has been running in the “params_reply_pending_process...
Hi Nordic Community
I'm doing a risk assessment, and I couldn't find a proper answer for the fallowing two question, it would be great if I could have your opinion and...
I am trying to set up the sniffer on nRF52832 DK PCA10040. I am not seeing the COM port on the Wireshark interface. I can see it on the device manager. I have looked at other...
Hi Everyone , I am using SDK v15.0 for nrf52840 with segger embedded studio.
I tried the example code given for blink freertos. I am able to run two tasks but as soon as...