Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
I have now removed all my experimental code and have returned to the more or less original verion of the main.c for assec_tracker, but still the application seems to be stuck...
We are using the Nordic nRF52840 on our current design. Currently, I am using nRF Toolbox -UART app on my
mobile phone to send data via 9 buttons available on the App. Everything...
I am trying to read the data of an MQ-6 sensor, which is its gas sensor, but the data I receive is not from the reading by the values it shows, if you know how to do it or...
Hi,
When the bootloader address resolves to something invalid, fds_init will hardfault. I think it should have some check and return a nice error code instead.
See an...
Hi,
I want to disable all four buttons to my rigado bmd 300 evaluation kit (pca10040 is the board config. the same as nrf52 DK ) in project ble_app_uart
I have tried to...
I'm powering an nrf52810 with a 3.3V regulator. I understand the internal LDO powers the system at 1.3 V. Are the GPIO pins and other peripheral devices outputting 3.3V for...
Hi
When I select the Generic Level server model and try to bind the app key I get an invalid model Error. I am using the nRF Mesh android app.
This might be relevant or...
Dear Nordic Support,
I am using ble_nus service on nRF52840 (BMD-340-A-R) + Raspberry Pi 3B+ ( https://github.com/IanHarvey/bluepy ). The nRF52840 is the peripheral and...
Hi,
I would like to know the I2C bus capacitance for the nrf52840. Do someone have the information please ?
My slave components are compliant for 400Khz and VDD is 3.3V...
I have gone through the tutorial on mesh experimental dimming and I was able to provision the BLE nodes, contol and dim the LED1 on the evaluation module with RTT viewer....
Hello everyone,
We are having a problem with the DFU function in our custom iOS app.
We are using DFU library version 4.5.1.
After updating SoftDevice and Bootloader...
I'm using the nRF52840 DK to develop my application using FreeRTOS while trying to achieve the lowest possible consumption. I'm having some issues so I went back to the ble_app_hrs_freertos_pca10056_s140...
hi
i use the example flashwriting in nRF5_SDK_15.3.0_59ac345, i set a table at 0xfd000:
// ProgramSection alignment="4" keep="Yes" load="yes" name=".tabletest" address_symbol...
Hello, I am using nRF9160 PCA10090 DK. I want to make my board as central device and scan for all nearby BLE devices and display its rrsi value and device id on a terminal...
